BTM404-02 Laird Technologies, BTM404-02 Datasheet

no-image

BTM404-02

Manufacturer Part Number
BTM404-02
Description
MODULE, BLUETOOTH, BISM2 PA, 3.3V
Manufacturer
Laird Technologies
Datasheet
1.BTM402-03.pdf (32 pages)

Specifications of BTM404-02

Compliance Standard
CE, FCC, IC, R, TTE
Supply Voltage Range
3.3V To 5V
Physical Interfaces
UART
Data Rate
300Kbps
Transmit Power
65mW
Receiving Signal Range
-87dBm
Operating Temperature
RoHS Compliant
Operating Temperature Range
-10°C To +85°C
Rohs Compliant
Yes
www.EZURiO.com
Long Range Bluetooth™ Serial Module
3.3V Bluetooth Module with Power Amplifier
Part Number: BTM404
1. General Description
EZURiO’s BISM II PA Bluetooth Serial Module is a fully integrated and qualified Class 1 Bluetooth
solution, which incorporates a power amplifier and low noise amplifier that maximises the RF link
budget to provide the greatest range of any Bluetooth Module. The module is designed for lowest cost
of integration and ownership for designers wishing to incorporate Bluetooth functionality into their
products. The module is qualified to Bluetooth Version 2.0.
The BISM II PA Bluetooth Serial Module is one of the most compact complete Bluetooth solutions,
making it ideal to integrate into handheld devices. The module includes a high sensitivity, high gain
antenna which provides excellent range.
Typical open field performance provides ranges of up to
1,000 metres at transmit powers of 65mW.
The BISM II PA Module is based on Cambridge Silicon Radio’s BlueCore 04 chipset.
The module
contain all of the hardware and firmware for a complete Bluetooth solution, requiring no further
components. The Module has an integrated, high performance antenna which is matched with the
Bluetooth RF and baseband circuitry. The firmware integrated into the BC04 chipset implements the
higher layer Bluetooth protocol stack, with support for applications requiring Generic Access Profile
(GAP), Service Discovery Profile (SDAP), Serial Port Profile (SPP), Dial Up Networking Profile (DUN),
Headset Profile (HSP), Hands Free Profile (HFP), File Transfer Profile (FTP) and OBEX (Client).
A virtual processor is used within the BC04 to implement an AT command processor. This interfaces
to the host system over a straight forward serial port using an extensive range of AT commands. The
AT command set abstracts the Bluetooth protocol from the host application, saving many months of
programming and integration time. It provides extremely short integration times for data oriented
cable replacement and voice applications.
Firmware is also included that provides programming
support for multi-point applications.
A low cost development system is available for fast product
evaluation and development.
Support is provided for low power modes that make the BISM II PA particularly applicable to battery
powered installations.
The Module can be configured so that it can be attached to a ‘dumb’ terminal or attached to a PC or
PDA for cable replacement applications.
In addition to the Bluetooth functionality, The BISM II PA Module provides access to 7 General I/O
lines and 2 analogue input lines. These can be configured to provide connection to simple devices
such as switches or LEDs without requiring any external processor. Both the GPIO and ADC lines can
be accessed either via the wired host UART connection, or remotely over the Bluetooth link.
The BISM II PA module is supplied in a small form factor pcb (22.0mm x 34.0mm x 7.6mm), that
connects to a main pcb using a 40 way Hirose connector. The interface is compatible with the BISM1
module and EZURiO’s 40 pin 802.11 modules.
The BISM II PA module is Lead-free and is RoHS
compliant and supports an industrial temperature range of -10°C to +85°C.
A key feature of the design is that the module is pin and format compatible with EZURiO’s range of
802.11 wireless LAN modules. This allows designers to manufacture a single version of pcb which can
accept either a Bluetooth or an 802.11 module, greatly reducing development time to generate a
range of wirelessly enabled products.
The compatible 802.11 modules are the WISMC01, which
contains a full TCP/IP stack, network drivers and a web server, and the WISMC02 which contains
wireless network drivers and a UDP stack with SLIP interface.
1
DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC
© 2007-8 EZURiO Ltd

Related parts for BTM404-02

Image
Part Number
Description
Manufacturer
Datasheet
Request R
BTM404
Part Number:
BTM404
Description:
MODULE BISM II W/PWR AMP 3.3V
Manufacturer:
Laird Technologies
Datasheet:
BTM404.pdf (2 pages)
ACC-001
Part Number:
ACC-001
Description:
Mounting Clip
Manufacturer:
Laird Technologies
ACC-003
Part Number:
ACC-003
Description:
Extension Cable
Manufacturer:
Laird Technologies
BISDK02BI-00
Part Number:
BISDK02BI-00
Description:
Bluetooth Serial Module Development Kit
Manufacturer:
Laird Technologies
BTM-411
Part Number:
BTM-411
Description:
BTM411
Manufacturer:
Laird Technologies
BTM511-07
Part Number:
BTM511-07
Description:
Simple Wireless Module
Manufacturer:
Laird Technologies
DVK-BTM411-02
Part Number:
DVK-BTM411-02
Description:
BLUETOOTH MODULE DEVELOPMENT KIT
Manufacturer:
Laird Technologies
DVK-BTM431
Part Number:
DVK-BTM431
Description:
Bluetooth 2.0 AT Data Module, Internal Antenna Development Kit
Manufacturer:
Laird Technologies
DVK-BTM511
Part Number:
DVK-BTM511
Description:
BLUETOOTH EVAL BOARD BTM511
Manufacturer:
Laird Technologies
Datasheet:
DVK-BTM511.pdf (2 pages)
DVK-BTM510
Part Number:
DVK-BTM510
Description:
Bluetooth / 802.15.1 Modules & Development Tools BLUETTH Multimed MODLE, No ANT DEVKIT
Manufacturer:
Laird Technologies
Datasheet:
DVK-BTM511.pdf (2 pages)
DVK-PRM122
Part Number:
DVK-PRM122
Description:
DEV KIT PRM122
Manufacturer:
Laird Technologies
Datasheet:
DVK-PRM122.pdf (2 pages)
DVK-PRM123
Part Number:
DVK-PRM123
Description:
DEV KIT PRM123
Manufacturer:
Laird Technologies
Datasheet:
DVK-PRM122.pdf (2 pages)
DVK-PRM112
Part Number:
DVK-PRM112
Description:
KIT FOR PRM112
Manufacturer:
Laird Technologies
Datasheet:
DVK-PRM113.pdf (2 pages)
DVK-PRM121
Part Number:
DVK-PRM121
Description:
DEV KIT PRM121
Manufacturer:
Laird Technologies
Datasheet:
DVK-PRM122.pdf (2 pages)
CM3312R111R-10
Part Number:
CM3312R111R-10
Description:
CHOKE COMMON MODE 110 OHMS SMD
Manufacturer:
Laird Technologies
Datasheet:
CM3322U610R-10.pdf (2 pages)

BTM404-02 Summary of contents

Page 1

... TCP/IP stack, network drivers and a web server, and the WISMC02 which contains wireless network drivers and a UDP stack with SLIP interface. DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC Typical open field performance provides ranges Firmware is also included that provides programming ...

Page 2

... Stop bits Default Serial parameters Levels Modem Control General Purpose Interface I/O ADC Audio Support SCO Channels PCM Interface DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC • Voice Applications • Industrial Automation • Automotive Applications Implementation Bluetooth v2.0 Class 1 2.400 – 2.4835 GHz ...

Page 3

... Warranty Development Tools Development Kit † DSR, DTR, RI and DCD are configurable either as GPIO or as modem control lines. DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC V2.0 compliant. Fully integrated. GAP (Generic Access Profile) SDP (Service Discovery Profile) SPP (Serial Port Profile) FTP Client ...

Page 4

... The Module is equipped with a 40-pin 0.5mm pitch board-to-board connector that connects to the application platform. Note that the underside (connector side) of the pcb contains a number of components. Sufficient clearance must be maintained on the mating pcb to guarantee clearance. DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC www.EZURiO.com 4 © 2007-8 EZURiO Ltd ...

Page 5

... UART_RX, UART_TX, UART_CTS, UART_RTS, UART_RI, UART_DCD and UART_DSR are all 3.0v level logic. For example, when RX and TX are idle they will be sitting at 3.0V. Conversely for handshaking pins CTS, RTS, RI, DCD, DSR treated as an assertion. DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC www.EZURiO.com Pin ...

Page 6

... Signal Levels for Interface, PCM, SPI and GPIO Signal Type Signal level Input V min=-0. max=0. min=2. max=3.4V IH Output DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC Min Max 0 200 -0.4 3.4 3.2 8.0 I/O Voltage level Comments I 3. 130mA typ 6 Ground terminals to be attached ...

Page 7

... Miscellaneous Signal Name Pin No I/O USB USB DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC Comments Shared with GPIO3 Direction may be programmed. Direction may be programmed. Comments Used to reprogram Flash Comments If unused keep pins open. PCM output signals are tri- stated when there is not an active SCO or eSCO connection ...

Page 8

... S508=S510=1000, S509=S511=11 Inquiry Mode, AT+BTI Connecting Mode (ATDxxx) Connected Mode (No Data Transfer) Connected Mode (Max Data Transfer) See section 8 for details of different low power modes. DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC V max=0.9V Active HIGH. The Reset input IL contains a 10kΩ pull down V min=2 ...

Page 9

... S Reg 507), this pin should be asserted by the host to ensure connection is maintained. A de-assertion is taken to mean that the connection should be dropped online command mode is being requested. DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC max: 40mW (16dBm) +2dBi typ. ...

Page 10

... The Module is compatible with the Motorola SSI TM interface and interfaces directly to PCM audio devices including the following: 6.1.4.1 Compatible Codec Chips • OKI 7702 single channel A-law and μ-law CODEC DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC Application /RXD /TXD /RTS /CTS ...

Page 11

... The BISM II PA firmware is provided with support for the profiles that are most commonly required for cable replacement applications. The current profiles supported by the AT command set firmware (point to point applications) include: DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC Description OKI 7702 single channel CODEC ...

Page 12

... Module possible to implement auto connect with a Bluetooth enabled mobile phone. • Automatically re-connect devices when a connection is dropped. DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC le. The profile to find other Bluetooth devices and the services of a serial cable for cable replacement applications. Profile support for connection to an external PSTN, GSM, GPRS or de more control over the headset operation ...

Page 13

... Decrease or increase the output power to suit your connection range • Configure the modules to work in Sniff and other low power modes. DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC This allows units to be placed in the discoverable state for a character ncoming AND / OR outgoing connections coming AND / OR outgoing connections. The ...

Page 14

... Register pairs 508/509 and 510/511 describe duty cycles when the module goes into scan modes while scanning that the highest current draw occurs. The DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC www.EZURiO.com In most cases better latency and power 14 © ...

Page 15

... Although the specification defines these parameters in terms of timeslots, the S register values have to be specified in units of milliseconds and the firmware does the necessary translation to timeslots. DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC www.EZURiO.com at the expense of response time. The ...

Page 16

... High Power Consumption T Slots N Slots M Slots (Negotiated) DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC Low Power Consumption T Slots T Slots T Slots T Slots N Slots M Slots (Negotiated) 16 www.EZURiO.com N Slots © 2007-8 EZURiO Ltd ...

Page 17

... This will lead to a drop in connection and may require a power cycle to reset the module. EZURiO recommend that the correct CTS/RTS handshaking protocol be adhered to for proper operation. DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC Function Function Input/Output from module ...

Page 18

... Assuming the Bluetooth address of the master to be <bdaddr_m> and that of the slave to be <bdaddr_s>, the master module is configured by sending it the following AT commands: AT&F* ATS512=1 ATS504=1 ATS507=2 ATS530=2000 AT&W AT+BTR<bdaddr_s> DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC www.EZURiO.com 18 © 2007-8 EZURiO Ltd ...

Page 19

... Assuming the Bluetooth address of the master to be <bdaddr_m> and that of the slave to be <bdaddr_s>, the master module is configured by sending it the following AT commands: AT&F* ATS512=1 ATS504=1 ATS530=2000 ATS532=7 AT&W AT+BTR<bdaddr_s> And the slave is configured by: AT&F* DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC www.EZURiO.com 19 © 2007-8 EZURiO Ltd ...

Page 20

... PIO lines, removing the need for a crystal on the customer’s main pcb. frequencies available are: • 8 MHz • 16 MHz For more implementation details, refer to EZURiO’s Application Note APN_06004_1v0 Crystal Output from BISM.pdf DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC www.EZURiO.com 20 © 2007-8 EZURiO Ltd The ...

Page 21

... The antenna finish may tarnish as a result of environmental effects and handling. This is a cosmetic effect and does not affect the RF performance. DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC Normally, antennas operating at 2.4GHz are affected by their However the optimum range is achieved when the two ...

Page 22

... Designers should carefully consider the location of the Module and the type of enclosure material that is used. To prevent mechanical damage, be car positioned flat against the host device. DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC eful not to force, bend or twist the Module. Be sure www.EZURiO.com ...

Page 23

... Hirose if they are to take advantage of this. Board Spacing Part number 3.3 mm NPR2005-153-3.3 4.1 mm NPR2005-153-4.1 5.1 mm NPR2005-153-5.1 See http://www.hirose.co.jp/cataloge_hp/e53700036.pdf DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC Source Matching HRS PCB Socket EZURiO / Richco CL537-0032-4-86 Richco CL537-0057-5-86 Richco CL537-0157-0-86 for detail information on the PCB socket. ...

Page 24

... Hirose Connector general specifica Parameter Number of Contacts Quantity delivered Voltage Current Rating Resistance Dielectric Withstanding Voltage Operating Temperature Contact Material DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC Stacking height 3.5 mm – 3.5 mm 4.0 mm 5.0 mm Specification (40 pin Board to Board connector) 40 2000 Connectors per Tape & Reel 50V ...

Page 25

... Co-location with other radio transmitting devices operating concurrently in the same band will require additional testing and certification. DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC Material PA , beige natural 5.0 mm 21.8N ...

Page 26

... Europe have a responsibility to notify the appropriate nominated body before commercial introduction. A list of nominated bodies is available at: http://eur-lex.europa.eu/LexUriServ/site/en/oj/2003/c_302/c_30220031212en00010414.pdf Further details on the notification procedure are given in EZURiO’s Application Note AN016 - Notification Requirements for Wireless Products. DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC www.EZURiO.com 26 © 2007-8 EZURiO Ltd ...

Page 27

... High Temp/Humidity 60ºC, 90%RH, 360 hours Operation Thermal shock -20 to 60ºC in 30min Electro Static Discharge EN55024:1998 & IEC61000-4-3 Drop Test 75cm to concrete, 3 axis x 2 cycles per corner DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC Min Typ Max -10 25 +85 ture Min Max Unit ...

Page 28

... Physical Dimensions 14.1 Mechanical Dimensions 14.1.1 Standard Module Location of Connector (Bottom View) All dimensions in mm Note that there are components on the underside of the pcb. See section 3.1 for details. DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC www.EZURiO.com 28 © 2007-8 EZURiO Ltd ...

Page 29

... The label contains the Part number and the unique Bluetooth address of the module. 14.4 Ordering Informa The Bluetooth PA Module described in this data sheet should be ordered using the part number below: Part Number BTM404 DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC http://www.hirose.co.jp/cataloge_hp/e32119372.pdf tion Description 3.3V Bluetooth PA Module with Antenna 29 www.EZURiO.com © ...

Page 30

... For cellular applications, the Wireless Development Kit also supports Siemens’ MC55 range of GSM/GPRS modules, which are pin compatible with EZURiO’s wireless LAN module. DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC www.Bluetooth.org 30 www ...

Page 31

... Please check with EZURiO Ltd for the most recent data before initiating or completing a design. Where reference is made to related products from other suppliers, EZURiO takes no responsibility for the information, availability or performance of such products. DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC www.EZURiO.com 31 © 2007-8 EZURiO Ltd ...

Page 32

... Bluetooth is a trademark owned by Bluetooth SIG, Inc., USA, and is licensed to EZURiO Ltd DSH_BTM404_0v5 BISM2 3V3 PA Data Sheet.DOC www.EZURiO.com 32 © 2007-8 EZURiO Ltd ...

Related keywords