HV857MG Supertex, HV857MG Datasheet

Display Drivers HVCMOS

HV857MG

Manufacturer Part Number
HV857MG
Description
Display Drivers HVCMOS
Manufacturer
Supertex
Datasheet

Specifications of HV857MG

Driver Type
EL Lamp Drivers
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Package / Case
MSOP-8
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
HV857MG
Quantity:
5 510
Part Number:
HV857MG
Manufacturer:
HV
Quantity:
20 000
Part Number:
HV857MG
Manufacturer:
SUPERTEX
Quantity:
19 963
Part Number:
HV857MG-G
Manufacturer:
PHISON
Quantity:
5 000
Part Number:
HV857MG-G
Manufacturer:
SUPERTEX
Quantity:
20 000
Features
Applications
Typical Application Circuit
Patented audible noise reduction
Patented lamp aging compensation
190 V
Patented output timing for high efficiency
Single cell lithium ion compatible
150nA shutdown current
Wide input voltage range 1.8 to 5.0V
Separately adjustable lamp and converter
frequencies
Output voltage regulation
Split supply capability
Available in 8-Lead MSOP and DFN packages
LCD backlighting
Mobile Cellular Phone
PDAs
Handheld wireless communication products
Global Positioning Systems (GPS)
PP
output voltage for higher brightness
V
V
DD
IN
+
_
+
_
ON = V
OFF =
0
DD
C
C
DD
IN
1235 Bordeaux Drive, Sunnyvale, CA 94089
Low Noise, High Voltage
Enable Signal
EL Lamp Driver IC
R
R
SW
EL
1
2
3
4
General Description
The Supertex HV857 is a high voltage driver designed for driving
Electroluminescent (EL) lamps of up to 5 square inches. The
input supply voltage range is from 1.8 to 5.0V. The device uses a
single inductor and a minimum number of passive components.
The nominal regulated output voltage that is applied to the EL
lamp is ±95V. The chip can be enabled/disabled by connecting
the resistor on RSW-Osc to VDD/GND.
The HV857 has two internal oscillators, a switching MOSFET,
and a high voltage EL lamp driver. The frequency for the switching
MOSFET is set by an external resistor connected between the
RSW-Osc pin and the supply pin VDD. The EL lamp driver
frequency is set by an external resistor connected between REL-
Osc pin and VDD pin. An external inductor is connected between
the LX and VDD pins or V
0.1µF capacitor is connected between CS and ground. The EL
lamp is connected between VA and VB.
The switching MOSFET charges the external inductor and
discharges it into the capacitor at CS. The voltage at CS will
start to increase. Once the voltage at CS reaches a nominal
value of 95V, the switching MOSFET is turned OFF to conserve
power. The outputs VA and VB are configured as an H bridge
and are switching in opposite states to achieve ±95V across the
EL lamp.
RSW-Osc
GND
VDD
REL-Osc
HV857
VB
LX
VA
CS
Tel: 408-222-8888
8
7
6
5
IN
L
X
for split supply applications. A 0.003-
D
www.supertex.com
C
EL Lamp
S
HV857

Related parts for HV857MG

HV857MG Summary of contents

Page 1

... IN Low Noise, High Voltage EL Lamp Driver IC General Description The Supertex HV857 is a high voltage driver designed for driving Electroluminescent (EL) lamps square inches. The input supply voltage range is from 1.8 to 5.0V. The device uses a single inductor and a minimum number of passive components. The nominal regulated output voltage that is applied to the EL lamp is ± ...

Page 2

... DD Pin Configuration 8-Lead MSOP VDD 3.00x3.00mm body RSW-Osc 1.10mm height (max) 0.65mm pitch REL-Osc HV857MG-G GND Pads are at the bottom of the package Exposed center pad is at ground potential Product Marking Value -0.5V to 6.5V -40°C to +85°C -65°C to +150°C 1.6W 300mW -0 ...

Page 3

... Units Conditions 150 µ 1.8 to 5.0V. See Figure See Figure See Figure 1 275 Hz See Figure 1 - kHz See Figure See Figure High Voltage Level Translator Equivalent to 3.0in lamp 2 2.0kΩ 10nF BAS21 5 220µH* 3.3nF, 100V ● Tel: 408-222-8888 ● www.supertex.com HV857 ...

Page 4

... Typical Performance Device Lamp Size HV857MG-G 3.0in 2 Typical Performance Curves for Figure 1.5 2.5 3.5 V (V) IN Brightness 1.5 2.5 3.5 V (V) IN 100 100 150 200 3.3V 20.0mA (EL Lamp = 3.0in 4.5 5.5 1 4.5 5 Brightness vs Inductor Value IN CS Brightness Iin l 250 300 350 400 Inductor Value (µ ...

Page 5

... If the input power is greater than IN IN ● 1235 Bordeaux Drive, Sunnyvale, CA 94089 5 resistor connected between REL-Osc and VDD EL decreases. As the EL lamp frequency increases, EL will decrease. The CS resistor by a factor EL decreases. With a given inductor ● Tel: 408-222-8888 ● www.supertex.com HV857 resistor value SW ...

Page 6

... Figure 2: Split Supply and Enable/Disable Configuration Enable Signal DD OFF = 0V Regulated Voltage = Audible Noise Reduction This section describes a method (patented) developed at Supertex to reduce the audible noise emitted by the EL lamps used in application sensitive to audible noise. Figure Figure 3: Typical Application Circuit for Audible Noise Reduction Enable OFF = Enable/Disable Confi ...

Page 7

... The noisiest waveform is a square wave and the quietest waveform has been assumed sine wave. After extensive research, Supertex has developed a wave- form that is quieter than a sine wave. The waveform takes the shape of approximately 2RC time constants for rising ...

Page 8

... NOM 0.75 0.02 (mm) MAX 0.80 0.05 JEDEC Registration MO-229, Variation WEEC-2, Issue C, Aug. 2003. * This dimension is not specified in the original JEDEC drawing. The value listed is for reference only. Drawings not to scale. Supertex Doc. #: DSPD-8DFNK73X3P065, Version B101008. E θ Seating Plane A3 Note ...

Page 9

... Supertex inc. does not recommend the use of its products in life support applications, and will not knowingly sell them for use in such applications unless it receives an adequate “product liability indemnification insurance agreement.” Supertex inc. does not assume responsibility for use of devices described, and limits its liability to the replacement of the devices determined defective due to workmanship ...

Related keywords