LQ084V3DG02 Sharp Microelectronics, LQ084V3DG02 Datasheet
LQ084V3DG02
Specifications of LQ084V3DG02
Available stocks
Related parts for LQ084V3DG02
LQ084V3DG02 Summary of contents
Page 1
... MODEL No. The technical literature is subject to change without notice. So, please contact SHARP or its representative before designing your product based on this literature. MOBILE LIQUID CRYSTAL DISPLY GROUP LITERATURE FOR LQ084V3DG02 Engineering department Mobile LCD Division Ⅲ SHARP CORPORATION LD –19Z60A No. DATE DEC．19．2007 ...
Page 2
... RECORDS OF REVISION LQ084V3DG02 SPEC No. DATE LD-19Z60A DEC.19.2007 REVISED No. PAGE - - SUMMARY - 1st Issue NOTE ...
Page 3
NOTICE This publication is the proprietary of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical for ...
Page 4
... Applicable TFT-LCD module This specification applies to the color TFT-LCD module, LQ084V3DG02. 2 Overview This module is a color active matrix transmissive LCD module incorporating amorphous silicon TFT (Thin Film Transistor composed of a color TFT-LCD panel, driver ICs, control circuits and power supply circuitry and a backlight unit ...
Page 5
Input Signal Assignment 4.1 TFT-LCD Panel driving section CN1 Used connector: IMSA-9637S-33Y902 (IRISO ELECTRONICS CO.,LTD.) Pin No. Symbol 1 GND 2 CK Clock signal for sampling each datum 3 Hsync Horizontal Sync signal 4 Vsync Vertical Sync signal 5 ...
Page 6
U/D=Low) (R/L=High, U/D=High) 4.2 Backlight section CN2 Pin no. Symbol 1 Power supply for LED (ch2 High voltage side) ＋ch2 2 Power supply for LED (ch1 High voltage side) ＋ch1 3 −ｃｈ１ Power supply for LED (ch1 ...
Page 7
Electrical characteristics 6.1 TFT-LCD Panel driving section Parameter Supply voltage Current dissipation Allowed input ripple voltage Input voltage (“Low” state) Input voltage (“High” state) Input leakage current (low) Input leakage current (High) [Note6-1] Vcc turn-on/off conditions 0 < t1 ...
Page 8
CK, R0~R5, G0~G5, B0~B5, Hsync, Vsync, ENAB, R/L and U/D [Note6-4] CK, R0~R5, G0~G5, B0~B5, Hsync, Vsync, and ENAB [Note6-5] R/L [Note6-6] U/D R0∼R5 G0∼G5 B0∼ ENAB CK I/F Connector R/L U/D ＶＣＣ 100Ω R0∼R5 ...
Page 9
Backlight driving Section The backlight system is an edge-lighting type with white-LED. The characteristics of LED are shown in the following table. (It is usually required to measure under the following condition. condition: I =100mA/Constant current drive,Ta=25℃±2℃) L Parameter ...
Page 10
Display Position in horizontal direction Display position in horizontal direction is designated by rising timing of ENAB signal Parameter ENAB signal Setup time Pulse width Phase difference between Hsync and ENAB signal When ENAB is fixed to “Low”, the ...
Page 11
Horizontal sync. 2.1V signal 0.8V 0.8V （Hsync） THc ＊Only when enable terminal is fixed “Low” Clock signal 0.8V 0.8V 0.8V （CK） C1＊ C103 ＊ C104＊(Number of clock) Data（R0∼5、 G0∼5、B0∼5） Horizintal invalid data period THe Data Enable signal 2.1V （ENAB） (active) ...
Page 12
Input Signals, Basic Display Colors and Gray Scale of Each Color Colors & Gray scale Gray Scale Black - 0 Blue ...
Page 13
Optical Specification Parameter Viewing angle Horizontal Range Vertical Contrast ratio Response time Rise Fall Chromaticity of white Luminance The optical specifications are measured 30 minute after turning LED on and in a dark room or equivalent condition, according to ...
Page 14
Definitions of viewing angle range: The best viewing angle of this module is slightly leaned to ６ o’clock from normal line. In the field where θ １２ The gray-scale in the field of 12 o’clock direction is brighter than ...
Page 15
Display Qualities Please refer to the Outgoing Inspection Standard. 11 Handling Instruction 11.1 Assembling the module 1) Be sure to design the cabinet so that the module can be installed without any extra stress such as warp or twist. ...
Page 16
Others The LCD has the nature that its performance is LCD module in direct sunlight or strong ultra violet ray. If stored at the temperatures lower than the rated storage temperature, the LC may freeze and it may cause ...
Page 17
Miscellaneous a) Variable resister has been set optimally before shipment not change any adjusted value. If adjusted value is changed, the specification may be not satisfied. b) Don’t disassemble this module, it may cause malfunction. c) Image ...
Page 18
...
Page 19
...