GRM21BR71H104KA01L Murata, GRM21BR71H104KA01L Datasheet - Page 87

• Manufacturer Part Number: GRM21BR71H104KA01L
• Description: CAPACITOR, 0805 100NF 50V CAPACITOR, 0805 100NF 50V
• Manufacturer: Murata
• Series: GRM21r

Specifications of GRM21BR71H104KA01L

• Tolerance (+ Or -): 10%
• Voltage: 50VDC
• Temp Coeff (dielectric): X7R
• Operating Temp Range: -55C to 125C
• Mounting Style: Surface Mount
• Construction: SMT Chip
• Case Style: Ceramic Chip
• Failure Rate: Not Required
• Wire Form: Not Required
• Product Length (mm): 2mm
• Product Depth (mm): 1.25mm
• Product Height (mm): 1.25mm
• Product Diameter (mm): Not Requiredmm
• Capacitance: .1uF
• Package / Case: 0805
• Voltage Rating, Dc: 50V
• Capacitor Dielectric Type: CERAMIC MULTI-LAYER
• Tolerance,: 10%
• Tolerance, -: 10%
• Temp, Op. Max: 125(DEGREE C)
• Temp,: ROHS COMPLIANT
• Lead Free Status / RoHS Status: Compliant

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
!Note
No.
10
11 Vibration
12
13
LLL/LLR/LLA/LLM Series Specifications and Test Methods (2)
1
2
3
4
5
6
7
8
9
Operating
Temperature
Range
Rated Voltage
Appearance
Dimensions
Dielectric Strength
Insulation
Resistance
Capacitance
Dissipation Factor
(D.F.)
Capacitance
Temperature
Characteristics
Adhesive Strength
of Termination
Solderability of
Termination
Resistance
to Soldering
Heat
1. This Specifications and Test Methods is downloaded from the website of Murata Manufacturing co.,ltd. Therefore, it's specifications are subject to change or our products in it may be discontinued without advance notice.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
0.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
2. This Specifications and Test Methods has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product
0.
Please check with our sales representatives or product engineers before ordering.
specifications before ordering.
Item
Appearance No defects or abnormalities
Capacitance Within the specified tolerance
D.F.
Appearance No marking defects
Capacitance
Change
D.F.
I.R.
Dielectric
Strength
R6: –55 to +85 C
R7, C7: –55 to +125 C
C8: –55 to +105 C
See the previous pages.
No defects or abnormalities
Within the specified dimension
No defects or abnormalities
50 · F min.
Within the specified tolerance
R6, R7, C7, C8: 0.120 max.
No removal of the terminations or other defect should occur.
R6, R7, C7, C8: 0.120 max.
75% of the terminations are to be soldered evenly
and continuously.
R6, R7, C7, C8: Within 7.5%
R6, R7, C7, C8: 0.120 max.
50 · F min.
No failure
Char.
R6
R7
C7
C8
When no "*" is added in PNs table, please refer to LLL/LLR/LLA/LLM Series Specifications and Test Methods (1).
LLL/LLR/LLA/LLM Series Specifications and Test Methods (2)
Temp. Range
When "*" is added in PNs table, please refer to LLL/LLR/LLA/LLM Series Specifications and Test Methods (2).
–55 to +125
–55 to +125
–55 to +105
–55 to +85
( C)
Specifications
Reference
Temp.
25 C
Cap. Change
Within 15%
Within 15%
Within 22%
Within 22%
The rated voltage is defined as the maximum voltage that may
be applied continuously to the capacitor.
When AC voltage is superimposed on DC voltage, V
whichever is larger, should be maintained within the rated
voltage range.
Visual inspection
Using calipers
No failure should be observed when 250% of the rated voltage
is applied between the terminations for 1 to 5 seconds,
provided the charge/discharge current is less than 50mA.
The insulation resistance should be measured with a DC voltage
not exceeding the rated voltage at 25 C and 75%RH max. and
within 1 minute of charging.
The capacitance/D.F. should be measured at 25 C at the
frequency and voltage shown in the table.
The capacitance change should be measured after 5 min. at
each specified temperature stage.
The ranges of capacitance change compared with the 25 C
value over the temperature ranges shown in the table should
be within the specified ranges.
• Initial measurement.
Perform a heat treatment at 150+0/-10 C for one hour and then
set for 24 2 hours at room temperature. Perform the initial
measurement.
Solder the capacitor to the test jig (glass epoxy board) using a
eutectic solder. Then apply 10N* force in parallel with the test
jig for 10 1 sec. The soldering should be done either with an
iron or using the reflow method and should be conducted with
care so that the soldering is uniform and free of defects such as
heat shock.
Solder the capacitor to the test jig (glass epoxy board) in
the same manner and under the same conditions as (10). The
capacitor should be subjected to a simple harmonic motion
having a total amplitude of 1.5mm, the frequency being varied
uniformly between the approximate limits of 10 and 55Hz. The
frequency range, from 10 to 55Hz and return to 10Hz, should
be traversed in approximately 1 minute. This motion should be
applied for a period of 2 hours in each of 3 mutually
perpendicular directions (total of 6 hours).
Immerse the capacitor in a solution of ethanol (JIS-K-8101) and
rosin (JIS-K-5902) (25% rosin in weight proportion). Preheat at
80 to 120 C for 10 to 30 seconds. After preheating, immerse in
eutectic solder solution for 2 0.5 seconds at 230 5 C, or
Sn-3.0Ag-0.5Cu solder solution for 2 0.5 seconds at 245 5 C.
Preheat the capacitor at 120 to 150 C for 1 minute. Immerse
the capacitor in a eutectic solder or Sn-3.0Ag-0.5Cu solder
solution at 270 5 C for 10 0.5 seconds.
Let sit at room temperature for 24 2 hours, then measure.
• Initial measurement.
Perform a heat treatment at 150+0/–10 C for one hour and
then let sit for 24 2 hours at room temperature. Perform the
initial measurement.
CV10 F (6.3V max.)
CV10 F (10V min.)
Capacitance
C>10 F
*5N (LLL15, LLL18, LLR18, LLA, LLM Series)
Test Method
Frequency
120 24Hz
1 0.1kHz
1 0.1kHz
Continued on the following page.
1.0 0.2Vrms
0.5 0.1Vrms
0.5 0.1Vrms
Voltage
P-P
or V
O-P
,
85
C02E.pdf
10.12.20