GRM3195C1H682JA01D Murata, GRM3195C1H682JA01D Datasheet - Page 12

• Manufacturer Part Number: GRM3195C1H682JA01D
• Description: CAPACITOR, 1206 6.8NF 50V CAPACITOR, 1206 6.8NF 50V
• Manufacturer: Murata
• Series: GRM31r

Specifications of GRM3195C1H682JA01D

• Tolerance (+ Or -): 5%
• Voltage: 50VDC
• Temp Coeff (dielectric): C0G
• Operating Temp Range: -55C to 125C
• Mounting Style: Surface Mount
• Construction: SMT Chip
• Case Style: Ceramic Chip
• Failure Rate: Not Required
• Wire Form: Not Required
• Product Length (mm): 3.2mm
• Product Depth (mm): 1.6mm
• Product Height (mm): 0.85mm
• Product Diameter (mm): Not Requiredmm
• Capacitance: 6800pF
• Package / Case: 1206
• Voltage Rating, Dc: 50V
• Capacitor Dielectric Type: CERAMIC MULTI-LAYER
• Tolerance,: 5%
• Tolerance, -: 5%
• Temp, Op. Max: 125(DEGREE C)
• Temp, Op.: ROHS COMPLIANT
• Tolerance: 5 %
• Voltage Rating: 50 Volts
• Operating Temperature Range: - 55 C to + 125 C
• Temperature Coefficient / Code: C0G (NP0)
• Product: General Type MLCCs
• Dimensions: 1.6 mm W x 3.2 mm L x 0.85 mm H
• Termination Style: SMD/SMT
• Lead Free Status / RoHS Status: Compliant

!Note
!Note
No.
16
17
Continued from the preceding page.
Humidity
Steady
State
Humidity
Load
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
Item
Appearance
Capacitance
Change
Q/D.F.
I.R.
Dielectric
Strength
Appearance
Capacitance
Change
Q/D.F.
I.R.
Dielectric
Strength
The measured and observed characteristics should satisfy the
specifications in the following table.
No marking defects
Within T5% or T0.5pF
(Whichever is larger)
30pF and over : QU350
10pF and over
30pF and below :
More than 1,000MΩ or 50Ω • F (Whichever is smaller)
No failure
The measured and observed characteristics should satisfy the
specifications in the following table.
No marking defects
Within T7.5% or T0.75pF
(Whichever is larger)
30pF and over : QU200
30pF and below :
More than 500MΩ or 25Ω • F (Whichever is smaller)
No failure
10pF and below :
C : Nominal Capacitance (pF)
C : Nominal Capacitance (pF)
Compensating Type
QU275W5C/2
QU200W10C
QU100+10C/3
Temperature
Specifications
R6, R7 : Within T12.5%
E4, F5 : Within T30%
[R6, R7]
W.V. : 25Vmin. : 0.05max.
W.V. : 16/10V : 0.05max.
W.V. : 6.3V
[E4]
W.V. : 25Vmin. : 0.05max.
[F5]
W.V. : 25Vmin.
W.V. : 16V/10V : 0.15max.
W.V. : 6.3Vmax. : 0.2max.
R6, R7 : Within T12.5%
E4 : Within T30%
F5 : Within T30%
[W.V. : 10Vmax.]
F5 : Within W30/Y40%
[R6, R7]
W.V. : 25Vmin. : 0.05max.
W.V. : 16/10V : 0.05max.
W.V. : 6.3V
[E4]
W.V. : 25Vmin. : 0.05max.
[F5]
W.V. : 25Vmin.
W.V. : 16V/10V : 0.15max.
W.V. : 6.3Vmax. : 0.2max.
High Dielectric Type
0.075max. (CF3.3µF)
0.125max. (CU3.3µF)
0.075max. (CF3.3µF)
0.125max. (CU3.3µF)
: 0.075max. (CF0.10µF)
: 0.125max. (CU0.10µF)
: 0.075max. (CF0.10µF)
: 0.125max. (CU0.10µF)
GRM Series Specifications and Test Methods
Let the capacitor sit at 40T2D and 90 to 95% humidity for
500T12 hours.
Remove and let sit for 24T2 hours (temperature compensating
type) or 48T4 hours (high dielectric constant type) at room tem-
perature, then measure.
Apply the rated voltage at 40T2D and 90 to 95% humidity for
500T12 hours. Remove and let sit for 24T2 hours (temperature
compensating type) or 48T4 hours (high dielectric constant
type) at room temperature, then measure. The charge/discharge
current is less than 50mA.
#Initial measurement for F5/10V max.
Apply the rated DC voltage for 1 hour at 40T2D.
Remove and let sit for 48T4 hours at room temperature.
Perform initial measurement.
Test Method
Continued on the following page.
C02E10.pdf 04.1.20
25
4