GRM3195C1H682JA01D Murata, GRM3195C1H682JA01D Datasheet - Page 13

• Manufacturer Part Number: GRM3195C1H682JA01D
• Description: CAPACITOR, 1206 6.8NF 50V CAPACITOR, 1206 6.8NF 50V
• Manufacturer: Murata
• Series: GRM31r

Specifications of GRM3195C1H682JA01D

• Tolerance (+ Or -): 5%
• Voltage: 50VDC
• Temp Coeff (dielectric): C0G
• Operating Temp Range: -55C to 125C
• Mounting Style: Surface Mount
• Construction: SMT Chip
• Case Style: Ceramic Chip
• Failure Rate: Not Required
• Wire Form: Not Required
• Product Length (mm): 3.2mm
• Product Depth (mm): 1.6mm
• Product Height (mm): 0.85mm
• Product Diameter (mm): Not Requiredmm
• Capacitance: 6800pF
• Package / Case: 1206
• Voltage Rating, Dc: 50V
• Capacitor Dielectric Type: CERAMIC MULTI-LAYER
• Tolerance,: 5%
• Tolerance, -: 5%
• Temp, Op. Max: 125(DEGREE C)
• Temp, Op.: ROHS COMPLIANT
• Tolerance: 5 %
• Voltage Rating: 50 Volts
• Operating Temperature Range: - 55 C to + 125 C
• Temperature Coefficient / Code: C0G (NP0)
• Product: General Type MLCCs
• Dimensions: 1.6 mm W x 3.2 mm L x 0.85 mm H
• Termination Style: SMD/SMT
• Lead Free Status / RoHS Status: Compliant

4
!Note
!Note
Table A
26
No.
18
*Nominal values denote the temperature coefficient within a range of 25D to 125D (for ∆C)/85D (for other TC).
GRM Series Specifications and Test Methods
Char. Code
Continued from the preceding page.
High
Temperature
Load
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specifications or to transact the approval sheet for product specificaions before ordering.
5C
6C
6P
6R
6S
6T
7U
1X
Item
Appearance
Capacitance
Change
Q/D.F.
I.R.
Dielectric
Strength
Nominal Values (ppm/D)*
W350 to Y1000
The measured and observed characteristics should satisfy the
specifications in the following table.
No marking defects
Within T3% or T0.3pF
(Whichever is larger)
30pF and over : QU350
10pF and over
30pF and below :
More than 1,000MΩ or 50Ω
No failure
10pF and below :
C : Nominal Capacitance (pF)
Y000 T030
Y000 T060
Y150 T060
Y220 T060
Y330 T060
Y470 T060
Y750 T120
Compensating Type
QU275+5C/2
QU200+10C
Temperature
Specifications
#
F (Whichever is smaller)
Max.
0.58
0.87
2.33
3.02
4.09
5.46
8.78
R6, R7 : Within T12.5%
E4 : Within T30%
F5 : Within T30%
F5 : Within
[R6, R7]
W.V. : 25Vmin. : 0.05max.
W.V. : 16/10V : 0.05max.
W.V. : 6.3V
[E4]
W.V. : 25Vmin. : 0.05max
[F5]
W.V. : 25Vmin.
W.V. : 16V/10V : 0.15max.
W.V. : 6.3Vmax. : 0.2max.
Y
High Dielectric Type
0.075max. (CF3.3µF)
0.125max. (CU3.3µF)
(CapF1.0µF)
W30/Y40% (CapU1.0µF)
: 0.075max. (CF0.10µF)
: 0.125max. (CU0.10µF)
Y55
Y0.24
Y0.48
Min.
0.72
1.28
2.16
3.28
5.04
Y
Capacitance Change from 25D (%)
Apply 200% of the rated voltage for 1000T12 hours at the
maximum operating temperature T3D. Let sit for 24T2 hours
(temperature compensating type) or 48T4 hours (high dielectric
constant type) at room temperature, then measure.
The charge/discharge current is less than 50mA.
#Initial measurement for high dielectric constant type.
Apply 200% of the rated DC voltage for one hour at the
maximum operating temperature T3D. Remove and let sit for
48T4 hours at room temperature. Perform initial measurement.
*150% for 500V and CU10µF
Max.
0.40
0.59
1.61
2.08
2.81
3.75
6.04
Y
Y30
Y0.17
Y0.33
Min.
0.50
0.88
1.49
2.26
3.47
Y
Test Method
Max.
0.25
0.38
1.02
1.32
1.79
2.39
3.84
Y
C02E10.pdf 04.1.20
Y10
Y0.11
Y0.21
Min.
0.32
0.56
0.95
1.44
2.21
Y