BFC246860104 Vishay, BFC246860104 Datasheet - Page 23

• Manufacturer Part Number: BFC246860104
• Description: Polyester Film Capacitors 100nF 10% 1000volts
• Manufacturer: Vishay

Specifications of BFC246860104

• Tolerance (+ Or -): 10%
• Voltage: 1000VDC/250VAC
• Temp Coeff (dielectric): PLYE
• Mounting Style: Through Hole
• Construction: Radial
• Failure Rate: Not Required
• Seated Plane Height: 22.5mm
• Product Diameter (mm): Not Requiredmm
• Product Height (mm): 22.5mm
• Product Depth (mm): 9.5mm
• Product Length (mm): 26mm
• Lead Spacing (nom): 22.5mm
• Lead Diameter (nom): 0.8mm
• Operating Temp Range: -55C to 105C
• Capacitance: .1uF
• Package / Case: Not Required
• Tolerance: 10 %
• Voltage Rating: 1 KVolts
• Termination Style: Radial
• Lead Spacing: 22.5 mm
• Product: Metallized Polyester Film Capacitors
• Lead Free Status / RoHS Status: Compliant

3. The voltage pulse slope (dU/dt) shall not exceed the rated voltage pulse slope in an RC-circuit at rated voltage and without
4. The maximum component surface temperature rise must be lower than the limits (see graph max. allowed component
5. Since in circuits used at voltages over 280 V peak-to-peak the risk for an intrinsically active flammability after a capacitor
6. When using these capacitors as across-the-line capacitor in the input filter for mains applications or as series connected with
Voltage Conditions for 6 Above
EXAMPLE
C = 330 nF - 100 V used for the voltage signal shown in next drawing.
U
The ambient temperature is 35 °C
Checking conditions:
1. The peak voltage U
2. The peak-to-peak voltage 80 V is lower than 2√2 x 63 Vac = 178 U
3. The voltage pulse slope (dU/dt) = 80 V/500 µs = 0.16 V/µs
4. The dissipated power is 60 mW as calculated with fourier terms
5. Not applicable
6. Not applicable
Voltage Signal
Document Number: 28105
Revision: 08-Dec-08
P-P
ALLOWED VOLTAGES
Maximum continuous RMS voltage
Maximum temperature RMS-overvoltage (< 24 h)
Maximum peak voltage (V
ringing. If the pulse voltage is lower than the rated DC voltage, the rated voltage pulse slope may be multiplied by U
divided by the applied voltage.
For all other pulses following equation must be fulfilled:
T is the pulse duration.
The rated voltage pulse slope is valid for ambient temperatures up to 85 °C. For higher temperatures a derating factor of 3 %
per K shall be applied.
temperature rise).
breakdown (short circuit) increases, it is recommended that the power to the component is limited to 100 times the values
mentioned in the table: “Heat conductivity”
an impedance to the mains the applicant must guarantee that the following conditions are fulfilled in any case (spikes and
surge voltages from the mains included).
This is lower than 20 V/µs (see specific reference data for each version)
The temperature rise for W
This is lower than 15 °C temperature rise at 35 °C, according figure max. allowed component temperature rise
= 80 V; U
2
×
T
∫
0
⎛
⎝
dU
------- -
dt
⎞
⎠
2
P
×
= 70 V; T
dt U
<
Rdc
P
Voltage
O-P
= 70 V is lower than 100 Vdc
1
×
= 0.5 ms; T
U
) (< 2 s)
⎛
⎝
P
dU
------- -
dt
max.
⎞
⎠
rated
= 8.5 mm and pitch = 15 mm will be 60mW/11 mW/°C = 5.5 °C
2
T
= 1 ms
1
For technical questions, contact: [e-mail]
MKT Radial Lacquered Type
T
2
DC Film Capacitors
U
P-P
T
1.25 x U
amb
1.6 x U
P-P
MKT 467, MKT 468, MKT 469
U
≤ 85 °C
Rac
Rdc
Rac
Vishay BCcomponents
Time
85 °C < T
0.8 x U
1.3 x U
U
amb
Rac
Rac
Rdc
≤ 105 °C
www.vishay.com
Rdc
and
73