314270-3 TE Connectivity, 314270-3 Datasheet
314270-3
Specifications of 314270-3
Related parts for 314270-3
314270-3 Summary of contents
Page 1
... Pneumatic Crimping Heads 314269–1 (shown in Figure 1), 314270–1, 314270–3, 1213001–1, and 314537–1 are designed to crimp PIDG Terminals and Splices, and PLASTI–GRIP Terminals and Splices onto solid or stranded copper wire size 26–14 AWG. Refer to Figure 2. The crimping head is used with 626 Pneumatic Tooling Assemblies 189721– ...
Page 2
Pneumatic Crimping Heads PLASTI-GRIP Terminal CRIMPING DOT PRODUCT HEAD CODE PIDG PIDG PLASTI-GRIP PIDG NOTE: CRIMPING DOT PRODUCT HEAD CODE PIDG NOTE: NOTE: 2 PIDG Type Terminal WIRE TERMINAL/SPLICE TERMINALS RANGE INSULATION (AWG) COLOR CODE MIN WIRE INSULATION TERMINAL/SPLICE RANGE ...
Page 3
Pneumatic Crimping Heads 3. HEAD INSTALLATION AND REMOVAL 3.1. Head Selection The crimping heads are color–coded to match the terminal and splice insulation color. Observe the embossed dots on the insulation of finished crimps to ensure that the correct combination ...
Page 4
Pneumatic Crimping Heads 5. Activate the tool to complete the crimp. Open crimping jaws by squeezing the rollers together simultaneously; then remove crimped terminal. 6. Refer to Section 5 and Figure 6 for crimp inspection. 4.2. Butt Splice Crimping Procedure ...
Page 5
Pneumatic Crimping Heads Positions Insulation Adjustment Pin(s) (Ref) Figure 5 6. Repeat adjustment as necessary until desired insulation grip is obtained. DO NOT use a tighter setting than required. B. PLASTI-GRIP Terminals NOTE PLASTI-GRIP terminals contain only a wire insulation ...
Page 6
Pneumatic Crimping Heads NOTE 6 Crimp Inspection ACCEPT REJECT PIDG Insulation Restricting Terminals PIDG and PLASTI-GRIP Terminals PIDG Butt Splice Figure 6 408-9586 D ...
Page 7
... This inspection requires the use of plug gages conforming to the dimensions shown in Figure 8. Tyco Electronics does not manufacture or market these gages. Suggested Plug Gage Design Wire Barrel Crimp Crimping Heads 314269-1, 314270-1, 314270-3, and 314537-1 Jaw Closure Configuration Crimping Head 1213001-1 Only Die Closure Configuration ...
Page 8
... JAW CLOSURE GAGE ELEMENT DIAMETERS CRIMPING DIMENSIONS (mm [IN.]) HEAD (mm [IN.]) GO 0.965-1.473 0.965-0.973 314270-1 [.0380-.0580] [.0380-.0383] 0.762-1.270 0.762-0.770 314270-3 [.0300-.0500] [.0300-.0303] 1.016-1.524 1.016-1.024 314269-1 [.0400-.0600] [.0400-.0403] 0.762-1.270 0.762-0.770 314537-1 [.0300-.0500] [.0300-.0303] 0.762-1.270 0.762-0.770 1213001-1 [ ...
Page 9
Pneumatic Crimping Heads Detail A Inspection of Wire Barrel Crimping Section Adjustment Pins in Position 1 (Ref) D Rev Detail B Inspection of Insulation Crimping Section Wire Barrel Jaws Bottomed But Not Under Pressure Insulation Jaws Bottomed But Not Under ...
Page 10
... Pneumatic Crimping Heads ITEM PART NO. FOR CRIMPING HEAD NO. 314269-1 314270- CUSTOMER REPLACEMENT PARTS 314537-1 1213001-1 Figure 10 408-9586 Crimping Head 314269-1 Shown (Ref) QTY PER DESCRIPTION HEAD D ...