ADL5371ACPZ-R7 Analog Devices Inc, ADL5371ACPZ-R7 Datasheet - Page 5

• Manufacturer Part Number: ADL5371ACPZ-R7
• Description: IC,RF Modulator,LLCC,24PIN,PLASTIC
• Manufacturer: Analog Devices Inc

Specifications of ADL5371ACPZ-R7

• Design Resources: Interfacing ADL5371 to AD9779A Dual-Channel, 1 GSPS High Speed DAC (CN0017)
• Function: Modulator
• Lo Frequency: 500MHz ~ 1.5GHz
• Rf Frequency: 500MHz ~ 1.5GHz
• P1db: 14.4dBm
• Noise Floor: -158.6dBm/Hz
• Output Power: 7.6dBm
• Current - Supply: 200mA
• Voltage - Supply: 4.75 V ~ 5.25 V
• Test Frequency: 900MHz
• Package / Case: 24-VFQFN, 24-CSP Exposed Pad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: ADL5371ACPZ-R7TR

PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Table 3. Pin Function Descriptions
Pin No.
1, 2
7, 10
11, 12
21, 22
3 to 6
14, 15
16 to 18
8, 9
13
19, 20, 23, 24
Mnemonic
COM1
COM2
COM3
COM4
VPS1
VPS2
VPS3 to VPS5
LOIP, LOIN
VOUT
IBBP, IBBN,
QBBN, QBBP
Exposed Paddle
Description
Input Common Pins. Connect to ground plane via a low impedance path.
Input Common Pins. Connect to ground plane via a low impedance path.
Input Common Pins. Connect to ground plane via a low impedance path.
Input Common Pins. Connect to ground plane via a low impedance path.
Positive Supply Voltage Pins. All pins should be connected to the same supply (V
adequate external bypassing, connect 0.1 μF capacitors between each pin and ground.
Adjacent power supply pins of the same name can share one capacitor (see Figure 23).
Positive Supply Voltage Pins. All pins should be connected to the same supply (V
adequate external bypassing, connect 0.1 μF capacitors between each pin and ground.
Adjacent power supply pins of the same name can share one capacitor (see Figure 23).
Positive Supply Voltage Pins. All pins should be connected to the same supply (V
adequate external bypassing, connect 0.1 μF capacitors between each pin and ground.
Adjacent power supply pins of the same name can share one capacitor (see Figure 23).
50 Ω Single-Ended Local Oscillator Input. Internally dc-biased. Pins must be ac-coupled.
AC-couple LOIN to ground and drive LO through LOIP.
Device Output. Single-ended RF output. Pin should be ac-coupled to the load. The output is
ground referenced.
Differential In-Phase and Quadrature Baseband Inputs. These high impedance inputs must be
dc-biased to 500 mV dc and must be driven from a low impedance source. Nominal characterized
ac signal swing is 700 mV p-p on each pin. This results in a differential drive of 1.4 V p-p with a
500 mV dc bias. These inputs are not self-biased and must be externally biased.
Connect to ground plane via a low impedance path.
COM1
COM1
VPS1
VPS1
VPS1
VPS1
Figure 2. Pin Configuration
1
2
3
4
5
6
Rev. 0 | Page 5 of 20
(Not to Scale)
TOP VIEW
F-MOD
18
17
16
15
14
13
VPS5
VPS4
VPS3
VPS2
VPS2
VOUT
S
S
S
). To ensure
). To ensure
). To ensure
ADL5371