DSPIC33FJ128MC706T-I/PT Microchip Technology, DSPIC33FJ128MC706T-I/PT Datasheet - Page 22

• Manufacturer Part Number: DSPIC33FJ128MC706T-I/PT
• Description: IC,DSP,16-BIT,CMOS,TQFP,64PIN,PLASTIC
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ128MC706T-I/PT

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 53
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 16x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TFQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MA330013 - MODULE PLUG-IN DSPIC33 100TQFPDV164033 - KIT START EXPLORER 16 MPLAB ICD2DM240001 - BOARD DEMO PIC24/DSPIC33/PIC32AC164327 - MODULE SKT FOR 64TQFP
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

dsPIC33F
FIGURE 6-1:
6.2
When a supply voltage is applied to the device, a
Power-on Reset is generated. A new Power-on Reset
event is generated if the supply voltage falls below the
device threshold voltage (V
pulse is generated when the rising supply voltage
crosses the POR circuit threshold voltage.
6.3
An Oscillator Start-up Timer (OST) is included to
ensure that a crystal oscillator (or ceramic resonator)
has started and stabilized. The OST is a simple, 10-bit
counter that counts 1024 T
the oscillator clock to the rest of the system. The time-
out period is designated as T
involved every time the oscillator has to restart (i.e., on
Power-on Reset (POR) and wake-up from Sleep). The
Oscillator Start-up Timer is applied to the LP oscillator,
XT and HS modes (upon wake-up from Sleep, POR
and BOR) for the primary oscillator.
DS70155C-page 20
SOSCO
SOSCI
OSC1
OSC2
Power-on Reset
Oscillator Start-up Timer/Stabilizer
(OST)
Internal Fast
RC (FRC)
OSCILLATOR SYSTEM BLOCK DIAGRAM
Secondary
Oscillator
Oscillator
Oscillator
Primary
32 kHz
OSC
POR
OST
cycles before releasing
). An internal POR
. The T
OST
Internal Low-Power
RC (LPRC)
Oscillator
time is
Module
Preliminary
PLL
Secondary Osc
Primary Osc
6.4
The primary function of the Watchdog Timer (WDT) is
to reset the processor in the event of a software
malfunction. The WDT is a free-running timer that runs
off the on-chip LPRC oscillator, requiring no external
component. The WDT continues to operate even if the
main processor clock (e.g., the crystal oscillator) fails.
The Watchdog Timer can be “Enabled” or “Disabled”
either through a configuration bit (FWDTEN) in the
Configuration register, or through an SFR bit
(SWDTEN).
Any device programmer capable of programming
dsPIC
PM3 Programmer) allows programming of this and
other configuration bits to the desired state. If enabled,
the WDT increments until it overflows or “times out”. A
WDT time-out forces a device Reset (except during
Sleep).
®
DSC devices (such as Microchip’s MPLAB
Switching
Watchdog Timer (WDT)
Control
Clock
Block
and
F
OSC
© 2005 Microchip Technology Inc.
To Timer1
Divide by 4
F
CY
®