DSPIC33FJ128MC708A-E/PT Microchip Technology, DSPIC33FJ128MC708A-E/PT Datasheet - Page 147

• Manufacturer Part Number: DSPIC33FJ128MC708A-E/PT
• Description: 16 Bit MCU/DSP 40MIPS 128KB FLASH 80 TQFP 12x12x1mm TRAY
• Manufacturer: Microchip Technology
• Series: dsPIC™ 33Fr

Specifications of DSPIC33FJ128MC708A-E/PT

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 69
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 18x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 80-TFQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

For example, suppose a 10 MHz crystal is being used
with “XT with PLL” as the selected oscillator mode. If
PLLPRE<4:0> = 0, then N1 = 2. This yields a VCO input
of 10/2 = 5 MHz, which is within the acceptable range of
0.8-8 MHz. If PLLDIV<8:0> = 0x1E, then M = 32. This
yields a VCO output of 5 * 32 = 160 MHz, which is within
the 100-200 MHz ranged needed.
If PLLPOST<1:0> = 0, then N2 = 2. This provides a F
of 160/2 = 80 MHz. The resultant device operating
speed is 80/2 = 40 MIPS.
FIGURE 9-2:
TABLE 9-1:
 2009 Microchip Technology Inc.
Fast RC Oscillator with Divide-by-N
(FRCDIVN)
Fast RC Oscillator with Divide-by-16
(FRCDIV16)
Low-Power RC Oscillator (LPRC)
Secondary (Timer1) Oscillator (SOSC)
Primary Oscillator (HS) with PLL
(HSPLL)
Primary Oscillator (XT) with PLL
(XTPLL)
Primary Oscillator (EC) with PLL
(ECPLL)
Primary Oscillator (HS)
Primary Oscillator (XT)
Primary Oscillator (EC)
Fast RC Oscillator with PLL (FRCPLL)
Fast RC Oscillator (FRC)
Note 1:
Source (Crystal, External Clock
or Internal RC)
Note 1: This frequency range must be satisfied at all times.
2:
Oscillator Mode
OSC2 pin function is determined by the OSCIOFNC Configuration bit.
This is the default oscillator mode for an unprogrammed (erased) device.
CONFIGURATION BIT VALUES FOR CLOCK SELECTION
dsPIC33FJXXXMCX06A/X08A/X10A PLL BLOCK DIAGRAM
dsPIC33FJXXXMCX06A/X08A/X10A
Divide by
PLLPRE
2-33
N1
Oscillator Source
0.8-8.0 MHz
Secondary
Here
Primary
Primary
Primary
Primary
Primary
Primary
Internal
Internal
Internal
Internal
Internal
OSC
Preliminary
(1)
X
EQUATION 9-3:
POSCMD<1:0>
Divide by
PLLDIV
2-513
F
VCO
CY
M
xx
xx
xx
xx
10
01
00
10
01
00
xx
xx
=
100-200 MHz
F
-------------
Here
OSC
2
F
VCO
(1)
=
1
-- -
2


PLLPOST
XT WITH PLL MODE
EXAMPLE
Divide by
10000000 32
--------------------------------- -
2, 4, 8
FNOSC<2:0>
N2
2 2 
111
110
101
100
011
011
011
010
010
010
001
000

12.5-80 MHz
DS70594B-page 147


Here
=
40 MIPS
(1)
F
Note
1, 2
OSC
1
1
1
1
1
1
1