TISP61089BD Bourns Inc., TISP61089BD Datasheet
TISP61089BD
Specifications of TISP61089BD
Available stocks
Related parts for TISP61089BD
TISP61089BD Summary of contents
Page 1
... Bellcore GR-1089-CORE, Issue 2 and ITU-T recommendations K.20, K.21 and K.45. DUAL FORWARD-CONDUCTING P-GATE THYRISTORS PROGRAMMABLE OVERVOLTAGE PROTECTORS TISP61089B High Voltage Ringing SLIC Protector TSP TSM A 6.5 4.6 3.4 2.3 1.3 Rated for ITU-T K.20, K.21 and K.45 Carrier Embossed Tape Reeled TISP61089BDR-S D Package (Top View) K1 (Tip (Gate (Ring internal connection ...
Page 2
TISP61089B High Voltage Ringing SLIC Protector Description (Continued) The SLIC line driver section is typically powered from 0 V (ground) and a negative voltage in the region of - -150 V. The protector gate is connected to this ...
Page 3
TISP61089B High Voltage Ringing SLIC Protector Recommended Operating Conditions C TISP61089B gate decoupling capacitor G TISP61089B series resistor for GR-1089-CORE first-level surge survival TISP61089B series resistor for GR-1089-CORE first-level and second-level surge survival R TISP61089B series resistor for GR-1089-CORE intra-building ...
Page 4
TISP61089B High Voltage Ringing SLIC Protector Parameter Measurement Information V GK(BO (BO (BO) Quadrant III Switching Characteristic Unless Otherwise Noted, All Voltages are Referenced to the Anode OCTOBER 2000 - REVISED ...
Page 5
TISP61089B High Voltage Ringing SLIC Protector Thermal Information PEAK NON-RECURRING AC vs CURRENT DURATION 20 RING AND TIP TERMINALS: 15 Equal I simultaneously 10 GROUND TERMINAL: 8 Current twice 1 ...
Page 6
TISP61089B High Voltage Ringing SLIC Protector Operation of Ringing SLICs using Multiple Negative Voltage Supply Rails Figure 4 shows a typical powering arrangement for a multi-supply rail SLIC. V BATL is a lower (smaller) voltage supply than V BATH . ...
Page 7
TISP61089B High Voltage Ringing SLIC Protector SLIC Parameter Values The table below shows some details of HV SLICs using multiple negative supply rails. Manufacturer INFINEON‡ SLIC Series SLIC-P‡ SLIC # PEB 4266 Data Sheet Issue 14/02/2001 Short Circuit Current 110 ...
Page 8
TISP61089B High Voltage Ringing SLIC Protector Gated Protectors (Continued) SLICs have become more sophisticated. To minimize power consumption, some designs automatically adjust the driver supply voltage to a value that is just sufficient to drive the required line current. For ...
Page 9
TISP61089B High Voltage Ringing SLIC Protector Gated Protectors (Continued) protection voltage, the length of the capacitor to gate terminal tracking should be minimized. Inductive voltages in the protector cathode wiring will also increase the protection voltage. These voltages can be ...
Page 10
TISP61089B High Voltage Ringing SLIC Protector Gated Protectors (Continued) Testing transistor CB, SCR AK off state and diode reverse blocking: The highest AK voltage occurs during the overshoot period of the protector. To make sure that the SCR and diode ...
Page 11
TISP61089B High Voltage Ringing SLIC Protector Application Circuit Figure 12 shows a typical TISP61089B SLIC card protection circuit. The incoming line conductors, Ring (R) and Tip (T), connect to the relay matrix via the series overcurrent protection. Fusible resistors, fuses ...
Page 12
TISP61089B High Voltage Ringing SLIC Protector ‘1089 Section 4.5.5 - Test Generators (Continued) The exception to these two conditions of independence and limit waveshape values is the alternative IEEE C.62.41, 1.2/50-8/20 combination wave generator which may be used for testing ...
Page 13
TISP61089B High Voltage Ringing SLIC Protector ‘1089 Section 4.5.6 - Test Connections The telecommunications port R and T terminals may be tested simultaneously or individually. Figure 14 shows connection for simultaneous (longitudinal) testing. Figure 15 shows the two connections necessary ...
Page 14
TISP61089B High Voltage Ringing SLIC Protector ‘1089 Section 4.5.9 - Intra-Building Lightning Surge Testing This test is for network equipment ports that do not serve outside lines. Table 3 shows the 2/10 tests used for this section. Dedicated intra- building ...
Page 15
TISP61089B High Voltage Ringing SLIC Protector ‘1089 Section 4.5.11 - Current-Limiting Protector Testing (Continued) The test generator has a voltage source that can be varied from zero to 600 V rms and an output resistance of 20 Ω to each ...
Page 16
TISP61089B High Voltage Ringing SLIC Protector ‘1089 Section 4.5.13 - Second-Level Power Fault Testing for Central Office Equipment (Continued) Open-circuit Test AC Duration RMS Voltage # s V 120 1 900 277 2 5 600 3 5 600 100 to ...
Page 17
TISP61089B High Voltage Ringing SLIC Protector ‘1089 Section 4.5.16 (Continued) Dedicated intra-building ports may use an R single cycle rating. For the TISP61089B to survive the full 900 s test, the series overcurrent protection to operate before the TISP61089B current-time ...
Page 18
TISP61089B High Voltage Ringing SLIC Protector Overcurrent and Overvoltage Protection Coordination (Continued) The overcurrent protector should not allow current-time durations greater than the TISP61089B current ratings, otherwise the TISP61089B may fail. A satisfactory fusible resistor performance is shown in Figure ...
Page 19
TISP61089B High Voltage Ringing SLIC Protector Overcurrent and Overvoltage Protection Coordination (Continued) PEAK AC vs CURRENT DURATION Ceramic PTC Thermistor 2 1.5 1 First Level 0.8 Tests # 1 ...
Page 20
TISP61089B High Voltage Ringing SLIC Protector Device Symbolization Code Devices will be coded as below. “TISP” trademark of Bourns, Ltd., a Bourns Company, and is Registered in U.S. Patent and Trademark Office. “Bourns” registered trademark of ...