ATV71HD30N4 SQUARE D, ATV71HD30N4 Datasheet - Page 2

• Manufacturer Part Number: ATV71HD30N4
• Description: SPEED DRIVE, 40HP, 460V, ATV71
• Manufacturer: SQUARE D

Braking torque
Synchronous motor control profile
Regulation loop
Motor slip compensation
Diagnostic
Output voltage
Insulation
Type of cable for mounting in an enclosure
Electrical connection
Tightening torque
Supply
Analogue input number
Analogue input type
Input sampling time
Response time
Absolute accuracy precision
Linearity error
Analogue output number
Analogue output type
Discrete output number
Discrete output type
Minimum switching current
Maximum switching current
Discrete input number
Discrete input type
2
< 150 % with braking or hoist resistor
30 % without braking resistor
Vector control without speed feedback
Adjustable PI regulator
Adjustable
Automatic whatever the load
Not available in voltage/frequency ratio (2 or 5 points)
Suppressable
1 LED red presence of drive voltage
<= power supply voltage
Electrical between power and control
With a NEMA Type1 kit: 3-strand UL 508 cable at 40 °C, copper 75 °C PVC
With an IP21 or an IP31 kit: 3-strand IEC cable at 40 °C, copper 70 °C PVC
Without mounting kit: 1-strand IEC cable at 45 °C, copper 70 °C PVC
Without mounting kit: 1-strand IEC cable at 45 °C, copper 90 °C XLPE/EPR
AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR terminal 2.5
mm² / AWG 14
L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB terminal 50 mm² /
AWG 1/0
AI1-/AI1+, AI2, AO1, R1A, R1B, R1C, R2A, R2B, LI1...LI6, PWR 0.6 N.m
L1/R, L2/S, L3/T, U/T1, V/T2, W/T3, PC/-, PO, PA/+, PA, PB 12 N.m / 102.2 lb.in
Internal supply for reference potentiometer (1 to 10 kOhm), 10.5 V DC +/- 5 % ,
<= 10 mA for overload and short-circuit protection
Internal supply, 24 V DC , voltage limits 21...27 V, <= 200 mA for overload and
short-circuit protection
2
AI1-/Al1+ bipolar differential voltage +/- 10 V DC, input voltage 24 V max , resolu-
tion 11 bits + sign
AI2 software-configurable current 0...20 mA , impedance 242 Ohm, resolution 11
bits
AI2 software-configurable voltage 0...10 V DC, input voltage 24 V max,
impedance 30000 Ohm, resolution 11 bits
AI1-/Al1+ 2 ms, +/- 0.5 ms for analog input(s)
Al2 2 ms, +/- 0.5 ms for analog input(s)
LI1...LI5 2 ms, +/- 0.5 ms for discrete input(s)
LI6 (if configured as logic input) 2 ms, +/- 0.5 ms for discrete input(s)
<= 100 ms in STO (Safe Torque Off)
AO1 2 ms, tolerance +/- 0.5 ms for analog output(s)
R1A, R1B, R1C 7 ms, tolerance +/- 0.5 ms for discrete output(s)
R2A, R2B 7 ms, tolerance +/- 0.5 ms for discrete output(s)
AI1-/Al1+ +/- 0.6 % for a temperature variation 60 °C
AI2 +/- 0.6 % for a temperature variation 60 °C
AO1 +/- 1 % for a temperature variation 60 °C
AI1-/Al1+, AI2 +/- 0.15 % of maximum value
AO1 +/- 0.2 %
1
AO1 software-configurable logic output 10 V <= 20 mA
AO1 software-configurable current 0...20 mA, impedance 500 Ohm, resolution 10
bits
AO1 software-configurable voltage 0...10 V DC, impedance 470 Ohm, resolution
10 bits
2
R1A, R1B, R1C configurable relay logic NO/NC, electrical durability 100000 cy-
cles
R2A, R2B configurable relay logic NO, electrical durability 100000 cycles
Configurable relay logic 3 mA at 24 V DC
R1, R2 on inductive load, 2 A at 250 V AC, cos phi = 0.4,
R1, R2 on inductive load, 2 A at 30 V DC, cos phi = 0.4,
R1, R2 on resistive load, 5 A at 250 V AC, cos phi = 1,
R1, R2 on resistive load, 5 A at 30 V DC, cos phi = 1,
7
LI1...LI5: programmable 24 V DC with level 1 PLC, impedance: 3500 Ohm
LI6: switch-configurable 24 V DC with level 1 PLC, impedance: 3500 Ohm
LI6: switch-configurable PTC probe 0...6 , impedance: 1500 Ohm
PWR: safety input 24 V DC, impedance: 1500 Ohm conforming to[pace]ISO
13849-1 level d