H2C-8-AC120-A Omron, H2C-8-AC120-A Datasheet
H2C-8-AC120-A
Specifications of H2C-8-AC120-A
Related parts for H2C-8-AC120-A
H2C-8-AC120-A Summary of contents
Page 1
... ON-delay ON-delay SPDT SPDT SPDT SPDT Parallel Independent 8-pin round socket Front terminal screws A = 1.25 sec 0.2 sec 0.5 sec H2C-8-AC24-B H2C-F-AC24-B H2C-8-AC120-A H2C-F-AC12-C H2C-8-AC120-B H2C-8-AC120-C H2C-8-AC240-A H2C-8-AC240-B H2C-8-AC240-C H2C Signal OFF-delay SPDT – Independent 8-pin round socket H2C-8R-AC24-A ...
Page 2
... VAC, 50/60 Hz for 1 minute between contact and control circuit and between contacts of different poles 30 million operations minimum 200,000 operations 250 VAC (p. H2C 7.5 min 1. min 0 120 120 min 0 H2C-8R Independent Signal OFF-delay (clutch) Voltage clutch signal SPDT – Panel, surface track 8-pin round socket 180 g (6.3 oz) ...
Page 3
... H2C Engineering Data I ELECTRICAL SERVICE LIFE Timing Charts In the schematic diagrams, each thick line indicates the external wiring. I H2C-8 ON-DELAY TIMER I H2C-8R SIGNAL OFF-DELAY TIMER I H2C-F ON-DELAY TIMER 3 H2C ...
Page 4
... H2C Dimensions Unit: mm (inch) I TIMERS H2C-8 and H2C-8R H2C-F I ACCESSORIES PF085A Bottom Surface or Track Mounting Socket P2CF-08 Track Mounting/Front Connecting Socket Eight M3.5 x 7.5 sems 70 max. (2.76 max. (0.16) (1.97) 4.5 3 Terminal Arrangement/ 7.8 (0.18) (0.12) Internal Connections (0.31) (Top View) 35 ...
Page 5
... Y92A-48G Finger Safe Terminal for P3G-08 Conforming to VDE0106/P100 Twelve, 6.4 dia. holes 34 47.4 Y92F-30 Mounting Adapter (For H2C-8 and H2C-8R) Adapter installs behind the panel ideal for side by side installation. Use P3GA-08 socket. 4.5 5 7.8 (0.18) (0.31) 3 1.3 35.4 Two 4 ...
Page 6
... When using a front cover for flush mounting, use the Y92F-30 Adapter. The Y92F-73 or Y92F-74 Flush Mounting Adapter cannot be used. Position to lock in the time setting knob. The set position of the time setting knob is fixed. The time setting ring is secured to the time setting knob. 6 H2C ...
Page 7
... H2C Y92H-1 Hold Down Clips Use these clips with H2C-8 and H2C-8R timers mounted in a PF085A socket. The pair of clips secure the timer to the socket in installations with significant vibration. PFP-100N, PFP-50N Mounting Track 4.5 (0.18 Length 1 m PFP-100N 50 cm PFP-50N 1 m PFP-100N2 ...
Page 8
... H2C Installation I SELECTING POWER FREQUENCY H2C motor timers are designed to operate accurately on either Hz. A selector switch is located on the rear of the case in the lower left-hand corner. Set the proper frequency for your installation before mounting the timer. If the power frequency does not match the setting, the time measurement will be inaccurate ...
Page 9
... Using Y92F-70 and Y92F-71 Adapters Install the H2C-8 and H2C-8R timer, face first, into the back side of the Y92F-70 or Y92F-71 adapter so the bezel fits snugly. Be sure the retaining clips at the back of the adapter fit into the slots on either side of the timer. Compress the top and bottom tabs of the adapter then push the adapter through the front side of the panel cutout ...
Page 10
... H2C P2CF-08 Socket (For H2C-8 and H2C-BR) Mounting The P2CF-08 socket has two hooks that secure the timer to the socket. Be sure to allow at least 20 mm (0.79 in) clearance above and below the socket to gain access and to release the hooks for servicing and maintenance. Insert timer into the socket. Latch hooks. Then clip the rear of the socket to the track ...