Z-10FW2Y-B Omron, Z-10FW2Y-B Datasheet

no-image

Z-10FW2Y-B

Manufacturer Part Number
Z-10FW2Y-B
Description
BASIC SWITCH
Manufacturer
Omron
Series
Zr
Datasheet

Specifications of Z-10FW2Y-B

Circuit
DPDT
Switch Function
On-Mom
Contact Rating @ Voltage
10A @ 125VAC
Actuator Type
Lever, Roller
Mounting Type
Chassis Mount
Termination Style
Screw Terminal
Operating Force
127gf
Contact Form
SPDT
Contact Rating
10 Amps at 250 Volts
Actuator
Roller Lever
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
Z10FW2YB
Best-selling Basic Switch Boasting
High Precision and Wide Variety
• A large switching capacity of 15 A with high repeat accuracy.
• A wide range of variations in contact form for your selection: basic,
• A series of standard models for micro loads is available.
• A series of molded terminal-type models incorporating safety
Model Number Structure
Configuration
General-purpose
• A variety of actuators is available for a wide range of application.
• The contact mechanism of models for micro loads is a crossbar
• Contact Gap:
• These Switches use a rubber boot on the actuator and adhesive fill
• Models with drip-proof terminal protective covers and molded
Maintained-contact models
split-contact, maintained-contact, and adjustable contact gap types.
terminal protective cover is available.
type with gold-alloy contacts, which ensures highly reliable
operations for micro loads.
between the case and cover to increase resistance to drips.
terminals with resin filling are also available.
General-purpose Basic Switch
Z
Basic Models
Split-contact models
H2: 0.20 mm (extra-high-sensitivity)
H:
G:
E:
F:
Drip-proof
Basic models
Be sure to read Safety Precautions on page 22 and Safety Precautions
for All Basic Switches.
0.25 mm (high-sensitivity, micro voltage current load)
0.5 mm (standard)
1.8 mm (high-capacity)
1.0 mm (split-contact models)
General-purpose
General-purpose
General-purpose
Drip-proof
Without terminal protective cover
With terminal protective cover
Molded terminal
• This type is identical in construction to the general-purpose basic
• Since the moving contacts are connected to a common terminal,
• Highly reliable micro load switching is ensured if the model is used
• The maintained-contact type has a reset button at the bottom of the
• Since the Switch has greater pretravel than overtravel, it is suitable
switch except that it has two pairs of simultaneous acting contacts
by splitting moving contacts.
either parallel or series connection is possible.
as a twin-contact switch.
switch case, in addition to the pushbutton (plunger) located on the
opposite side of the reset button. Use these buttons alternately.
for use in reversible control circuits, manual reset circuits, safety
limit circuits, and other circuits which are not preferable for
automatic resetting. (For further details, refer to individual
datasheets.)
Split-contact Models
Maintained-contact Models
Refer to page 3.
Refer to page 5.
Refer to page 5.
Refer to page 2.
Refer to page 4.
Refer to page 4.
CSM_Z_DS_E_2_1
1

Related parts for Z-10FW2Y-B

Z-10FW2Y-B Summary of contents

Page 1

... Use these buttons alternately. • Since the Switch has greater pretravel than overtravel suitable for use in reversible control circuits, manual reset circuits, safety limit circuits, and other circuits which are not preferable for automatic resetting. (For further details, refer to individual datasheets.) CSM_Z_DS_E_2_1 1 ...

Page 2

... Terminals None : Solder terminal B : Screw terminal (with toothed washer) B5V : Screw terminal with terminal cover (for Z-15G@A55 only) Note: For combinations of models, Ordering Information on page Standard Models (Drip-proof Type/Molded Terminals) Z-@55-M@@ @M (1) (2)(3) (4) (1) Drip-proof Type (2) Lead Outlets ...

Page 3

... The pin plungers of reverse-type models are continuously pressed by the actuator levers with compression coil springs and the pin plungers are freed by operating the levers. Reverse-type models are highly vibration- and shock-resistive because the pin plungers are normally pressed. Accessories (Terminal Covers, Actuators, and Separators): Refer to Z/A/X/DZ Common Accessories and Z/X/DZ Common Accessories. Extra-high ...

Page 4

... Reverse-type models are highly vibration- and shock-resistive because the pin plungers are normally pressed. Minimum High-sensitivity order lot (pcs) --- --- --- --- --- --- 10 Z-15HW24-B Z-15HW78-B --- --- --- --- Maintained-contact Models F (1.0 mm) Actuator Model Pin plunger --- Z-10FY-B Slim spring plunger --- Z-10FSY-B Hinge lever --- Z-10FDY-B --- Z-10FQY-B --- Z-10FQ22Y-B --- Z-10FWY-B --- Z-10FW22Y-B --- Z-10FW2Y-B --- Z-10FM22Y-B Z Model Z-15ER Z-15ESR Z-15EWR 4 ...

Page 5

... The tip is made of resin. Minimum Order Lot The following models are available at the minimum order lot specified below. Orders must be placed per lot. Accessories (Terminal Covers, Actuators, and Separators): Refer to Z/A/X/DZ Common Accessories and Z/X/DZ Common Accessories. ) Standard G (0.5 mm) Not provided ...

Page 6

... VDC 0.75 0.75 250 VDC 0.3 0.3 * Figures in parentheses are for the Z-15HW52, Z-15HW78(-B) and Z-15H2(-B) models, the AC ratings of these models are 125 and 250 V only. Z-15 (Flexible Rod Models) Non-inductive load (A) Rated voltage Resistive load Lamp load NC NO ...

Page 7

... Contact gap H: 600 VAC, 50/60 Hz for 1 min Dielectric strength Contact gap E: 1,500 VAC, 50/60 Hz for 1 min Between current-carrying metal parts and ground, and between each terminal and non-current-carrying metal parts 2,000 VAC, 50/60 Hz for 1 min Vibration Malfunction Hz, 1.5-mm double amplitude *5 resistance ...

Page 8

... Note: The Z-15GM is a reversible model and the NO and NC positions are reversed. Molded Terminals COM (Black) (Red) NC (White indicates wire color. Note: The Z-15GM is a reversible model and the NO and NC positions are reversed. Structure Drip-proof Construction • Without Terminal Protective Cover Rubber boot Fixed contact (b) ...

Page 9

... Appropriate terminal screw tightening torque: 0.78 to 1.18 N·m. Note: With reverse action models (Z-15GM), the positions of NO and NC terminals are reversed. Dimensions and Operating Characteristics The models, illustrations, and graphics are for screw-terminal models (-B). The “-A” at the end of the model number for solder terminal models has been omitted. For details of the terminals, see above ...

Page 10

... On the model Z-15GQ3-B, PT can be set to a value larger than that for the Z- 15GQ the model Z-15GQ8-B, operating 9.2 position can be adjusted by providing a screw in the plunger section. ...

Page 11

... Hinge Lever Z-15GW-B Z-15GW32-B Z-15HW-B Z-10FWY-B 20.2 16.9 Z-15GW3-B (Lever Length: 56R)* * The external dimensions of the actuator vary. Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. ± 0.25 23.3 12.7 dia. × 4.8 *1 M12 × 1 +0.075 4.2 dia ...

Page 12

... Low-force Wire Hinge Lever Z-15HW52-B Z-15HW78-B (Lever Length: 110R The external dimensions of the actuator vary. Note: AC electrical ratings 125/250 V. Short Hinge Roller Lever Z-15GW22-B Z-01HW22-B Z-15HW22-B Z-10FW22Y-B Z-15EW22-B Z-15GW2-B * Z-15HW2-B * Z-10FW2Y The external dimensions of the actuator vary. (Lever Length: 48.5R) Z-15GW22-B Z-15HW22-B OF max. 1. ...

Page 13

... Short Hinge Cross Roller Lever Z-15GW49-B Z-15GW54-B (Lever Length: 48.7R) * 20.2 16.9 * The external dimensions of the actuator vary. Hinge Roller Lever Z-15GW25-B 20.2 16.9 Unidirectional Short Hinge Roller Lever Z-15GW2277-B 34.1 max. 20.2 16.9 Reverse Hinge Lever ** Z-15GM-B 20.2 17.4 Reverse Short Hinge Roller Lever ** ...

Page 14

... OP +0.075 4.2 -0.025 Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. Note: With reverse action models (Z-15GM), the positions of NO and NC terminals are reversed. The above illustration is for model without terminal protective cover. 3.9 dia. 23.3 ± 0.25 +0.075 4 ...

Page 15

... OF max. RF min. OT *min. 23.9 MD max. 9.2 FP max. 20 17.5±0 When operating, be sure not to exceed 1.6 mm. Z 5.30 N 1.12 N 1.8 mm 5.5 mm 5.30 N 1.12 N 1.8 mm 5.30 N 1.12 N 1.8 mm 1.96 N 0.14 N 1 ...

Page 16

... FP max. ± 0.2 17.45 OP 19±1 Stainless-steel lever 4 max. RF min. 9.2 OT min. MD max. FP max. 28.2 mm ± 0.2 17.45 OP 19±0 Stainless-steel lever Z-15GW2255-B Z-01HW2255-B OF max. 1. min. 0.41 N 9.2 OT min. 2 max. 0 max. 32.9 mm ± 0.2 OP 30.2±0 1.96 N 0.14 N 1.6 mm 1.3 mm 1.86 N ...

Page 17

... Reverse Short Hinge Roller Lever * Z-15GM2255-B 20.2 17.4 Reverse Hinge Roller Lever * Z-15GM255-B 20.2 17.4 * The pin plungers of reverse-type models are continuously pressed by the actuator levers with compression coil springs and the pin plungers are freed by operating the levers. Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. ...

Page 18

... Use only the area within the top the rod as the operating part. (Do not use the area that falls within 100 mm from the mounting hole as the operating part. Using this area may cause damage to the steel wire.) *3. The steel wire can be replaced if damaged. (Model: Lever for HNJS55 ...

Page 19

... Panel Mount Plunger PT Z-15GQA55-B5V OP 16.3 19.2 Panel Mount Roller Plunger PT Z-15GQ22A55-B5V OP 16.3 19.2 Panel Mount Cross-roller Plunger PT Z-15GQ21A55-B5V OP 16.3 19.2 Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions. 6SR * ± 0.25 23.3 +0.075 4.2 -0.025 +0.1 4.36 dia. -0.05 +0 ...

Page 20

... Short Hinge Roller Lever Z-15GW22A55-B5V 20.2 16.9 19.2 Hinge Roller Lever Z-15GW2A55-B5V 20.2 16.9 19.2 Unidirectional Short Hinge Roller Lever Z-15GW2277A55-B5V 34.1 max. 20.2 16.9 Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions 26.2 13.9 +0.075 4.2 -0.025 +0.1 4 ...

Page 21

... Reset button *2 ± 0.1 25.4 17.45 49.2 *1. Stainless steel lever *2. Plastic plunger a c Size (mm) a Lead wire 12 VSF 19 VCT 2.3 dia. 2.3SR *1 Reset position Plunger 7.1 min. OF max. 1. max. OT min. ...

Page 22

... IP62) in locations subject to floating dirt and dust. Other models do not have a protective structure. Wiring For wiring, use a wire size that is appropriate for the applied voltage and the supplied current. When soldering the Switch, make sure that the capacity of the soldering iron maximum. Do not take more than solder any part of the Switch ...

Page 23

... Tightening The suitable tightening torque for screw terminals is given below. Screw terminals except for those on Split-contact Models (Z-10FY- B): 0.78 to 1.18 N·m Screw terminals on Split-contact Models (Z-10FY-B): 0.49 to 1.18 N·m Operation • Make sure that the switching speed and frequency are is within the specified ranges ...

Page 24

... Flexible Rod Switch (Z-15@NJ@55, Drip-proof) • When the rod is fully swung, the Switch may operate when the lever Accessories (Order Separately) Refer to Z/A/X/DZ Common Accessories for details about Terminal Covers, Separators, and Actuators. Drip-proof Terminal Cover (Order Separately) The Drip-proof Terminal Protective Cover is provided for maintenance for Z-@A55-B5V Switches. ...

Page 25

... Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS ...

Related keywords