S82Y-VM30D Omron, S82Y-VM30D Datasheet - Page 8

• Manufacturer Part Number: S82Y-VM30D
• Description: MOUNTING BRKT G DIN-RAIL 300W
• Manufacturer: Omron

Specifications of S82Y-VM30D

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: S82YVM30D

Construction and Nomenclature
■ Nomenclature
■ Output Color Label
8
Open-frame Models
S8VM-100@@/S8VM-100@@D
Open-frame Models
Open-frame Models
S8VM-150@@/S8VM-150@@D
Note: Refer to page 14.
S8VM-015@@/S8VM-015@@D
S8VM-030@@/S8VM-030@@D
S8VM-050@@/S8VM-050@@D
100-W Models
15-W, 30-W, 50-W Models
150-W Models
300-W, 600-W, 1,500-W Models
This color label identifies the output voltage by color.
Switch Mode Power Supply
Color label identifying output voltage
12
12
12
12
11
11
5
4
3
2
1
11
11
5
4
3
2
1
5
4
3
2
1
12
12
12
12
S8VM-100@@C@/S8VM-10024A@/P@
Covered Models
S8VM-150@@C@/S8VM-15024A@/P@
Covered Models
S8VM-015@@C@/S8VM-01524A@
S8VM-030@@C@/S8VM-03024A@
S8VM-050@@C@/S8VM-05024A@/P@
Covered Models
8 9 10
8 9 10
Green: 5 V
Blue:
Yellow: 15 V
White: 24 V
6 7
S8VM
10
12 V
9
8
7
6
7
6
Note: 1. The fuse is located on the (L) side. It is NOT user-replace-
1
2
3
4
5
6
7
8
9
10
11
12
No.
(15-W, 30-W, 50-W, 100-W, 150-W Models)
AC input terminals (L), (N)
PE terminal: Protective earthing terminal
(S8VM-@@@@@C@/S8VM-@@@@@A@/
S8VM-@@@@@P@)
FG terminal: Frame ground terminal
(S8VM-@@@@@/S8VM-@@@@@D)
DC output terminals (-V), (+V)
Output indicator (DC ON: Green)
Output voltage adjuster (V. ADJ)
Undervoltage alarm indicator 1
(DC LOW1: Yellow) (See note 3.)
Undervoltage alarm indicator 2
(DC LOW2: Red) (See note 3.)
Undervoltage alarm output terminal 1:
(DC LOW1) (See note 4.)
Undervoltage alarm output terminal 2:
(DC LOW2) (See note 4.)
Common terminal for undervoltage alarm
output (See note 4.)
Remote sensing terminals (See note 5.)
Short bars (See note 5.)
2. If mounting is performed using a DIN Rail, the protective
3. S8VM-@@@24A@/P@ only
4. S8VM-05024A@/P@, S8VM-10024A@/P@, S8VM-
5. When not using the remote sensing function, leave the short
6. A@ models: Common terminal (emitter)
able.
earthing connection is the panel mounting hole shown in the
figure below.
(A protective earthing connection stipulated in safety stan-
dards is used. Connect the ground completely (S8VM-
@@@@@D only)).
Ground terminal: M3 (Depth: 8 mm max.)/Ground wire:
AWG 18
15024A@/P@ only. Housing and terminals of the connector
for undervoltage detection output are also provided. For de-
tails, refer to Undervoltage Alarm Output Connector Har-
ness Manufacture Method on page 33 under Safety
Precautions.
bar in the same state as when shipped.
P@ models: Common terminal (collector)
Name
Ground
Protective earthing
connection
Connect the input lines to
these terminals. (See note 1.)
Connect the ground line to this
terminal. (See note 2.)
Connect the load lines to these
terminals.
Lights (green) while a direct
current (DC) output is ON.
Use to adjust the voltage.
Lights only when a momentary
drop in output voltage is de-
tected. This status is main-
tained.
Lights only when the output
voltage drops to approximately
20 V or lower.
Outputs only when a momen-
tary drop in output voltage is
detected. This status is main-
tained.
(The transistor turns OFF
when a voltage drop occurs.)
Outputs only when the output
voltage drops to approximately
20 V or lower.
(The transistor turns OFF
when a voltage drop occurs.)
Common terminal (See note
6.) for terminals 8 and 9
Correct the voltage drop in the
load lines.
---
Function