D10BFPQ BANNER ENGINEERING, D10BFPQ Datasheet - Page 4

• Manufacturer Part Number: D10BFPQ
• Description: D10BFPQ QD 6 PIN PICO RED
• Manufacturer: BANNER ENGINEERING
• Type: Fiber Opticr

Specifications of D10BFPQ

• Brand/series: D10 Expert™
• Current, Switching: 150 mA
• Function: Fiber Optic
• Ip Rating: IP50
• Mounting Type: Bracket
• Output: NPN/PNP
• Primary Type: Photoelectric
• Sensing Mode: Selectable
• Technology: Photoelectric
• Termination: 6-Wire Connector
• Voltage, Supply: 30 VDC
• Accessories Available: Cordsets and Plastic Fiber Optic Cable

4
Dynamic TEACH is best used when a machine or process may not be stopped for
teaching. It programs the sensor during actual sensing conditions, taking multiple
samples of the light and dark conditions and automatically setting the threshold at the
optimum level (see Figure 3).
Dynamic TEACH activates the sensor’s adaptive threshold system, which continuously
tracks minimum and maximum signal levels, and automatically maintains centering of
the switchpoint between the light and dark conditions. The adaptive threshold system
remains in effect during RUN mode. The adaptive routine saves to non-volatile memory
at least once per hour.
When Dynamic TEACH mode is used, the output ON state (Light or Dark Operate) will
remain as it was last programmed. To change the output ON state, use SETUP mode
(see page 8).
Dynamic TEACH and Manual Adjust
The switchpoint may be adjusted (fine-tuned) whenever the sensor is in RUN mode
by clicking the “+” and “-” buttons. However, when a manual adjustment is made, the
adaptive threshold system is disabled (cancelled).
P/N 117830 rev. E
• Establishes a single switching threshold
•
•
•
•
•
Press and Hold Dynamic
Continue to hold push button.
Present Output ON and OFF
Release push button.
push button > 2 seconds.
conditions.
Push Button
Dynamic TEACH and Adaptive Thresholds
•
•
•
•
Hold remote line
Continue to hold remote
Present Output ON and
Release remote line/
low (to ground)
> 2 seconds.
line low (to ground).
OFF conditions.
switch.
or
or
or
Remote Line
T
T
T
T
T
T
T
T
T
T
T
T
T T T
T
T
T T T
T
T
T T T
T
T
T
T
T
T
Power LED: OFF
Output LED: OFF
Bargraph: LO & DO alternately flashing
Power LED: OFF
Output LED: OFF
Bargraph: LO & DO alternately flashing
TEACH Accepted
Power LED: ON
Bargraph:
Sensor returns to Run mode with new settings.
TEACH Unacceptable
Power LED: OFF
Bargraph:
Sensor returns to Run mode without changing settings.
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
One LED flashes to show
#1, 3, 5, 7 alternately flash
relative contrast (good signal
difference shown; see table
above)
T
to show failure
T
T
T
T
T
Banner Engineering Corp. • Minneapolis, MN U.S.A
T
T
T
T
Figure 3. Dynamic TEACH (Light Operate
(no signal)
(no signal)
(no signal)
Darkest
Darkest
Following
Darkest
Bargraph
TEACH
6 to 8
4 to 5
2 to 3
LED
Darkest Taught
Output OFF
Result
1
Condition
Output OFF
Output OFF
shown)
between taught conditions
Excellent: Very stable operation.
Good: Minor sensing variables will
not affect sensing reliability.
Low: Minor sensing variables may
affect sensing reliability.
Unreliable: Consider an alternate
sensing scheme.
Sensing window size
threshold midway
Sensor positions
Relative Signal Difference/
Manual Adjust
Manual Adjust
Manual Adjust
adjusted by
adjusted by
adjusted by
Output ON
condition
Position
Position
sensing
Single
Recommendation
Output ON
Output ON
Lightest Taught
Condition
Output OFF
Most Light
Most Light
Most Light
(saturated
(saturated
(saturated
signal)
signal)
signal)