D10BFPQ BANNER ENGINEERING, D10BFPQ Datasheet - Page 8

no-image

D10BFPQ

Manufacturer Part Number
D10BFPQ
Description
D10BFPQ QD 6 PIN PICO RED
Manufacturer
BANNER ENGINEERING
Type
Fiber Opticr
Datasheet

Specifications of D10BFPQ

Brand/series
D10 Expert™
Current, Switching
150 mA
Function
Fiber Optic
Ip Rating
IP50
Mounting Type
Bracket
Output
NPN/PNP
Primary Type
Photoelectric
Sensing Mode
Selectable
Technology
Photoelectric
Termination
6-Wire Connector
Voltage, Supply
30 VDC
Accessories Available
Cordsets and Plastic Fiber Optic Cable
Manual Adjust is used during RUN mode and is accomplished via the push buttons only. Its behavior depends on whether a switching
threshold or a sensing window is used.
Switching Threshold:
• Fine-tunes sensing sensitivity
• Press “+” to increase; press “-” to decrease
Sensing Window:
• Adjusts sensing window size (tolerance) for the single-point target condition
• Press “+” to increase; press “-” to decrease
The lighted bargraph LEDs move to reflect the increase or decrease.
In addition to its configuration function, the remote input may be used to disable the push buttons for security. Disabling the push
buttons prevents undesired tampering with the configuration settings. Connect the gray wire of the sensor as described on page 2, and
four-pulse to either enable or disable the push buttons:
8
SETUP mode is used to change sensor output response for:
• Light or Dark operate
• 30-millisecond pulse stretcher (OFF-delay), if required.
• 200 µs high-speed response
If SETUP mode configuration is interrupted and remains inactive for 60 seconds, the sensor
returns to RUN mode with the most recent settings (i.e., exits and saves current selection).
SET UP mode operates in the “background,” while the outputs are active; changes are
updated instantly.
T
P/N 117830 rev. E
T
T
T T T
B_028256
0.04 seconds ≤ “Click” ≤ 0.8 seconds
0.8 seconds
> 2 seconds
buttons > 2 seconds.
Press and hold both push
LEDs show desired settings.
Click either push button until
buttons > 2 seconds.
Press and hold both push
T
Push Button
T
or
T
T
T
T T T
T
T
0.8 seconds
> 2 seconds
T
T
T
T
SETUP Mode
T
T
T
T
T
T
B_028256
T
T
T
T
0.04 seconds ≤ T ≤ 0.8 seconds
NOTE: Double-pulsing the
remote line will cause the
setting to “back up” one step.
or
line.
Double-pulse remote
until LEDs show desired
settings.
T
Pulse the remote line
T
T
> 2 seconds.
or
T
Hold remote line low
T
T
T
T
T
T
Remote Line
T
T
T T T
T
T
T
T
T
0.8 seconds
> 2 seconds
T
T
T
T
T
T
T
T
T
T
T
T
Push Button Disable
T
T
T
T
T
T
T
T
T
Manual Adjust
T
1x
2x
3x
4x
5x
6x
7x
T
T
T
T
T
T
T
T
T
T
T
T
• Green Power LED turns OFF.
• Output LED remains active.
• Icons continue to display
• Bargraph turns OFF.
Sensor toggles through eight setting combinations, in the
following order:
• Green Power LED turns ON.
T
T
T
T
T
T
current setup.
with new settings.
Sensor returns to RUN mode
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T T T
T
T
T
T
0.8 seconds
> 2 seconds
T
T
T
T
1x
2x
3x
4x
5x
T
T
T
T
LO - Normal Speed - No Delay (default)
DO - Normal Speed - No Delay
LO - High Speed -
DO - High Speed -
LO - Normal Speed - Delay
DO - Normal Speed - Delay
LO - High Speed -
DO - High Speed -
T
T
T
T
T
T
T
T
T
T
Banner Engineering Corp. • Minneapolis, MN U.S.A
T
T
T
T
T
T
T
T
T
T
T
T
Figure 7. SETUP mode
T
T
T
T
T
T
T
T
T
Result
1x
2x
3x
4x
5x
6x
7x
Indicators
T
T
SETUP
T
T
Status
No Delay
No Delay
Delay
Delay
T
T
T
T
T
T
{
T
T
T
T
T
T
T
T
DO
HS
LO
static
T
T
T
T
T
T
T
T
T
T
8
7
6
5
4
3
2
1
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
Press
and hold both
push buttons
> 2 seconds
to access
SETUP mode
1x
2x
3x
4x
5x
6x
7x

Related parts for D10BFPQ