PQ60033ETL30PRS-G SYNQOR, PQ60033ETL30PRS-G Datasheet
PQ60033ETL30PRS-G
Specifications of PQ60033ETL30PRS-G
Related parts for PQ60033ETL30PRS-G
PQ60033ETL30PRS-G Summary of contents
Page 1
... UL 60950-1 recognized (US & Canada), basic insula- tion rating • TUV certified to EN60950-1 • Meets 72/23/EEC and 93/68/EEC directives which facilitates CE Marking in user’s end product • Board and plastic components meet UL94V-0 flammabil- ity requirements www.synqor.com T echnical T echnical S pecification S ...
Page 2
... Notes: 1. SENSE(–) should be connected to Vout(–) either remotely or at the converter. 2. Leave TRIM pin open for nominal output voltage. 3. SENSE(+) should be connected to Vout(+) either remotely or at the converter. www.synqor.com Doc.# 005-2ET633F Rev. A 35-75 V Input: 35-75 V Input: 3.3 V Output: Output: 3.3 V ...
Page 3
... Note 1: Output voltage ripple can exceed maximum specification during startup when output voltage is less than 1.4V. Additional output capacitance will mitigate this start- up ripple behavior. For applications requiring reduced output voltage ripple and noise, consult SynQor applications support (e-mail: support@synqor.com) Note 2: Higher values of isolation capacitance can be added external to the module. ...
Page 4
... Needle Flame Test (IEC 695-2-2) IEC 61000-4-2 GR-1089-CORE Telcordia (Bellcore) GR-513 • An external input fuse must always be used to meet these safety requirements. Contact SynQor for official safety certificates on new releases or download from the SynQor website. QUALIFICATION TESTING Parameter P # Units ...
Page 5
... C (nominal input voltage). ° Figure 6: Thermal plot of converter at 28.5 amp load current (94.05W) with 70 C air flowing at the rate of 200 LFM. Air is flowing across the ° converter from 3 to pin 1 (nominal input voltage). www.synqor.com 35-75 V Input: 35-75 V Input: 3.3 V Output: Output: 3.3 V ...
Page 6
... Ch 2: ON/OFF input (5V/div). Figure 12 Output voltage response to step-change in load current (50%- : 75%-50% of Iout(max): dI/dt = 1A/µs). Load cap: 470µF, 30 mΩ ESR tanta- lum cap and 1µF ceramic cap Vout (50mV/div Iout (10A/div). www.synqor.com Doc.# 005-2ET633F Rev. A 35-75 V Input: 35-75 V Input: 3 ...
Page 7
... Figure 18: Load current (20A/div function of time when the con- F 100mΩ ESR tantalum µ verter attempts to turn on into a 15mΩ short circuit. Top trace (1ms/div expansion of the on-time portion of the bottom trace (40ms/div). www.synqor.com Doc.# 005-2ET633F Rev. A 35-75 V Input: 35-75 V Input: 3 ...
Page 8
... Figure 22: Magnitude of incremental input impedance ( for minimum, nominal, and maximum input voltage at full rated power www.synqor.com 35-75 V Input: 35-75 V Input: 3.3 V Output: Output: 3 Current: Current Eighth-brick ...
Page 9
... OVP does not trigger, even during load transients. Vin(-). There ON/OFF ON/OFF Vin( _ Vin Positive Logic (Permanently Enabled) 5V TTL/ ON/OFF CMOS Vin Direct Logic Drive www.synqor.com 35-75 V Input: 35-75 V Input: 3.3 V Output: Output: 3 Current: Current Eighth-brick P ackage: P ...
Page 10
... Over- Temperature Shutdown value. It will allow the converter to turn on again when the temperature of the sensed location falls by the amount of the Over-Temperature Shutdown Restart Hysteresis value. www.synqor.com 35-75 V Input: 35-75 V Input: 3.3 V ...
Page 11
... Input System Instability: This condition can occur because any DC/DC converter appears incrementally as a negative resistance load. A detailed application note titled “Input System Instability” is available on the SynQor website which provides an understanding of why this instability arises, and shows the preferred solution for correcting it. ...
Page 12
... Hexavalent Chromium, Mercury, Polybrominated Biphenyls (PBB), and Polybrominated Diphenyl Ether (PBDE) in Electrical and Electronic Equipment. This SynQor product is available as 6/6 RoHS compliant. SynQor’s RoHS addendum available at our RoHS Compliance / Lead Free Initiative web page or e-mail us at rohs@synqor.com. , and the Restart Inhibit 3 OFF ON ...
Page 13
... SynQor. Information furnished by SynQor is believed to be accurate and reliable. However, no responsibility is assumed by SynQor for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of SynQor ...