WM8903LGEFK/RV Wolfson Microelectronics, WM8903LGEFK/RV Datasheet - Page 7

no-image

WM8903LGEFK/RV

Manufacturer Part Number
WM8903LGEFK/RV
Description
Audio CODECs ULTRA LOW PWR HI FI CODEC
Manufacturer
Wolfson Microelectronics
Datasheets

Specifications of WM8903LGEFK/RV

Audio Codec Type
Stereo Codec
No. Of Adcs
2
No. Of Dacs
2
No. Of Input Channels
6
No. Of Output Channels
8
Adc / Dac Resolution
24bit
Sampling Rate
96kHz
Operating Temperature Range
-40°C To +85°C
Rohs Compliant
Yes
Adcs / Dacs Signal To Noise Ratio
96dB
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
WM8903LGEFK/RV
Manufacturer:
SHARP
Quantity:
93
Part Number:
WM8903LGEFK/RV
Quantity:
2 386
Part Number:
WM8903LGEFK/RV
Manufacturer:
WOFLSON
Quantity:
20 000
Part Number:
WM8903LGEFK/RVA
Manufacturer:
SHARP
Quantity:
709
Part Number:
WM8903LGEFK/RVA
Manufacturer:
WOFLSON
Quantity:
20 000
Pre-Production
ELECTRICAL CHARACTERISTICS
TERMINOLOGY
1.
2.
3.
4.
5.
6.
7.
COMMON TEST CONDITIONS
Unless otherwise stated, the following test conditions apply throughout the following sections:
Additional, specific test conditions are given within the relevant sections below.
w
to the left channel only, the right channel amplitude is measured. Then a full scale signal is applied to the right
channel only and the left channel amplitude is measured. The worst case channel separation is quoted as a ratio.
output path. With the signal path idle, a small signal sine wave is summed onto the power supply rail, The amplitude
of the sine wave is measured at the output port and expressed as a ratio.
Signal-to-Noise Ratio (dB) – SNR is the difference in level between a full scale output signal and the device output
noise with no signal applied, measured over a bandwidth of 20Hz to 20kHz. This ratio is also called idle channel
noise. (No Auto-zero or Automute function is employed).
Total Harmonic Distortion (dB) – THD is the difference in level between a 1kHz full scale sinewave output signal and
the first seven harmonics of the output signal. The amplitude of the fundamental frequency of the output signal is
compared to the RMS value of the next seven harmonics and expressed as a ratio.
Total Harmonic Distortion + Noise (dB) – THD+N is the difference in level between a 1kHz full scale sine wave output
signal and all noise and distortion products in the audio band. The amplitude of the fundamental reference frequency
of the output signal is compared to the RMS value of all other noise and distortion products and expressed as a ratio.
Channel Separation (dB) – is a measure of the coupling between left and right channels. A full scale signal is applied
Channel Level Matching (dB) – measures the difference in gain between the left and the right channels.
Power Supply Rejection Ratio (dB) – PSRR is a measure of ripple attenuation between the power supply pin and an
All performance measurements carried out with 20kHz AES17 low pass filter for distortion measurements, and an
A-weighted filter for noise measurement. Failure to use such a filter will result in higher THD and lower SNR and
Dynamic Range readings than are found in the Electrical Characteristics. The low pass filter removes out of band
noise; although it is not audible it may affect dynamic specification values.
DCVDD = 1.2V
DBVDD = 1.8V
AVDD = CPVDD =1.8V
Ambient temperature = +25°C
Audio signal: 1kHz sine wave, sampled at 48kHz with 24-bit data resolution
PP, Rev 3.1, August 2009
WM8903
7

Related parts for WM8903LGEFK/RV