IRF3709ZPBF International Rectifier, IRF3709ZPBF Datasheet
IRF3709ZPBF
Specifications of IRF3709ZPBF
Related parts for IRF3709ZPBF
IRF3709ZPBF Summary of contents
Page 1
... Notes through are on page 12 www.irf.com V DSS 30V TO-220AB IRF3709Z @ 10V GS @ 10V GS 300 (1.6mm from case) Typ. i ––– g ––– IRF3709ZPbF IRF3709ZSPbF IRF3709ZLPbF HEXFET Power MOSFET R max Qg DS(on) 6.3m : 17nC 2 D Pak TO-262 IRF3709ZS IRF3709ZL Max. Units 30 V ± ...
Page 2
Static @ T = 25°C (unless otherwise specified) J Parameter BV Drain-to-Source Breakdown Voltage DSS ∆ΒV /∆T Breakdown Voltage Temp. Coefficient DSS J R Static Drain-to-Source On-Resistance DS(on) V Gate Threshold Voltage GS(th) ∆V /∆T Gate Threshold Voltage Coefficient GS(th) ...
Page 3
VGS TOP 10V 9.0V 7.0V 5.0V 4.5V 4.0V 3.5V BOTTOM 3.0V 100 3.0V ≤ 60µs PULSE WIDTH Tj = 25° Drain-to-Source Voltage (V) Fig 1. Typical Output Characteristics 1000 100 ...
Page 4
0V MHZ C iss = SHORTED C rss = oss = iss 1000 C oss C ...
Page 5
Limited By Package 100 125 Case Temperature (°C) Fig 9. Maximum Drain Current vs. Case Temperature 0.50 1 0.20 0.10 0.05 ...
Page 6
125°C 7.00 6. 25°C 5.00 4.00 10.0 20.0 30.0 40.0 50 Drain Current (A) Fig 12. On-Resistance vs. Drain Current Current Regulator Same Type as D.U.T. Vds 50KΩ .2µF ...
Page 7
D.U.T + • • - • + - R • • • SD • Fig 17. Fig 18a. Switching Time Test Circuit V DS 90% 10% V Fig 18b. Switching Time Waveforms www.irf.com Driver Gate Drive P.W. ...
Page 8
Power MOSFET Selection for Non-Isolated DC/DC Converters Control FET loss conduction switching drive This can be expanded and approximated by × loss rms ds(on ) ⎛ ...
Page 9
Dimensions are shown in millimeters (inches) 10.54 (.415) 10.29 (.405) 2.87 (.113) 2.62 (.103) 4 15.24 (.600) 14.84 (.584 14.09 (.555) 13.47 (.530) 1.40 (.055) 3X 1.15 (.045) 2.54 (.100) 2X NOTES: 1 DIMENSIONING & TOLERANCING PER ...
Page 10
Dimensions are shown in millimeters (inches ...
Page 11
TO-262 Package Outline TO-262 Part Marking Information EXAMPLE: T HIS IS AN IRL3103L LOT CODE 1789 AS S EMBLED ON WW 19, 1997 EMBLY LINE "C" Note: "P" embly line pos ition ...
Page 12
D Pak Tape & Reel Infomation Dimensions are shown in millimeters (inches) TRR FEED DIRECTION 1.85 (.073) 1.65 (.065) TRL FEED DIRECTION 330.00 (14.173) MAX. NOTES : 1. COMFORMS TO EIA-418. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION MEASURED @ ...
Page 13
Note: For the most current drawings please refer to the IR website at: http://www.irf.com/package/ ...