DIODE PIN SWITCH 100V 1A MINIPAK

 

HMPP-3890-TR1

Manufacturer Part NumberHMPP-3890-TR1
DescriptionDIODE PIN SWITCH 100V 1A MINIPAK
ManufacturerAvago Technologies US Inc.
HMPP-3890-TR1 datasheets

Availability: By request

International delivery:

Warranty: 60 days

Shipping & payment terms

Added to cart

 

Specifications of HMPP-3890-TR1

Package / Case4-MiniPak (1412)Diode TypePIN - Single
Voltage - Peak Reverse (max)100VCurrent - Max1A
Capacitance @ Vr, F0.3pF @ 5V, 1MHzResistance @ If, F2.5 Ohm @ 5mA, 100MHz
ConfigurationSingleReverse Voltage5 V
Forward Continuous Current1 AFrequency RangeSHF
Termination StyleSMD/SMTCarrier Life0.2 us
Maximum Diode Capacitance0.3 pF at 5 VMaximum Operating Temperature+ 150 C
Maximum Series Resistance @ Maximum If2.5 Ohms at 5 mAMaximum Series Resistance @ Minimum If3.8 Ohms at 1 mA
Minimum Operating Temperature- 65 CMounting StyleSMD/SMT
Lead Free Status / RoHS StatusContains lead / RoHS non-compliantPower Dissipation (max)-
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
8
Page 8
9
Page 9
10
Page 10
11
12
13
Page 1/13

Download datasheet (517Kb)Embed
Next
HMPP-389x Series
MiniPak Surface Mount RF PIN Switch Diodes
Data Sheet
Description/Applications
These ultra-miniature products represent the blending of
Avago Technologies’ proven semiconductor and the latest
in leadless packaging technology.
The HMPP-389x series is optimized for switching applications
where low resistance at low current and low capacitance
are required. The MiniPak package offers reduced parasitics
when compared to conventional leaded diodes, and lower
thermal resistance.
Low junction capacitance of the PIN diode chip, combined
with ultra low package parasitics, mean that these prod-
ucts may be used at frequencies which are higher than
the upper limit for conventional PIN diodes.
Note that Avago’s manufacturing techniques assure that
dice packaged in pairs are taken from adjacent sites on
the wafer, assuring the highest degree of match.
The HMPP-389T low inductance wide band shunt switch
is well suited for applications up to 6 GHz.
Minipak 1412 is a ceramic based package, while Minipak
QFN is a leadframe based package.
Package Lead Code Identification (Top View)
Single
Anti-parallel
3
4
3
2
1
2
#0
#2
(Minipak 1412)
(Minipak 1412)
Shunt Switch
Anti-parallel
Cathode
Anode
3
4
3
2
1
2
Anode
Cathode
T
#3
(Minipak 1412)
(Minipak QFN)
[Under Development]
Features
• Surface mount MiniPak package
• Better thermal conductivity for higher power dissipa-
tion
• Single and dual versions
• Matched diodes for consistent performance
• Low capacitance
• Low resistance at low current
• Low FIT (Failure in Time) rate*
• Six-sigma quality level
* For more information, see the Surface Mount Schottky Reliability
Data Sheet.
Pin Connections and Package Marking
3
AA
2
Product code
Parallel
Notes:
1. Package marking provides orientation and
4
3
4
identification.
2. See “Electrical Specifications” for appropri-
ate package marking.
1
2
1
#5
(Minipak 1412)
Parallel
4
3
4
1
2
1
#4
(Minipak QFN)
[Under Development]
4
1
Date code

HMPP-3890-TR1 Summary of contents

  • Page 1

    ... Note that Avago’s manufacturing techniques assure that dice packaged in pairs are taken from adjacent sites on the wafer, assuring the highest degree of match. The HMPP-389T low inductance wide band shunt switch is well suited for applications GHz. Minipak 1412 is a ceramic based package, while Minipak QFN is a leadframe based package ...

  • Page 2

    ... HMPP-389x Series Absolute Maximum Ratings Symbol Parameter I Forward Current (1 µs pulse Peak Inverse Voltage IV T Junction Temperature j T Storage Temperature stg q Thermal Resistance [2] jc Notes: 1. Operation in excess of any one of these conditions may result in permanent damage to the device +25°C, where T is defined to be the temperature at the package pins where contact is ...

  • Page 3

    ... MiniPak 141 HMPP-389x Series Typical Performance = +5 °C (unless otherwise noted), each diode 0 100 I – FORWARD BIAS CURRENT (mA) F Figure 1. Total RF Resistance vs. Forward Bias Current. 200 160 V = –2V R 120 – –10V FORWARD CURRENT (mA) Figure 4. Typical Reverse Recovery Time vs. Reverse Voltage. 3 0.50 0.45 ...

  • Page 4

    ... MiniPak QFN HMPP-389x Series Typical Performance = +5 °C (unless otherwise noted), each diode T C 100 10 1 0.1 0 100 I - FORWARD BIAS CURRENT (mA) F Figure 6. Total RF Resistance at 5 °C vs. Forward Bias Current 200 160 V = –2V R 120 – –10V FORWARD CURRENT (mA) Figure 9. Typical Reverse Recovery Time vs. Re- verse Voltage ...

  • Page 5

    Typical Applications RF COMMON BIAS 1 BIAS 2 Figure 11. Simple SPDT Switch Using Only Positive Bias. RF COMMON BIAS Figure 13. Very High ...

  • Page 6

    ... Given a thin epitaxial I region, the diode designer can trade off the device’s total resistance (R capacitance (C and I region. The HMPP-3890 was designed with the 930 MHz cellular and RFID, the 1.8 GHz PCS and 2.45 GHz RFID markets in mind. Combining the low resistance shown in Figure 15 with a typical total capacitance of 0 ...

  • Page 7

    ... Linear Equivalent Circuit In order to predict the performance of the HMPP-3890 as a switch necessary to construct a model which can then be used in one of the several linear analysis programs presently on the market. Such a model is given in Figure 16, where given in Figure 1 and Figure 2. Careful examination of Figure 16 will reveal ...

  • Page 8

    ... Testing the HMPP-389T on the Demo-board Introduction The HMPP-389T PIN diode is a high frequency shunt switch. It has been designed as a smaller and higher performance version of the HSMP-389T (SC-70 package). The DEMO-HMPP-389T demo-board allows customers to evaluate the performance of the HMPP-389T without having to fabricate their own PCB. Since a shunt switch’s isolation is limited primarily by its parasitic inductance, the product’ ...

  • Page 9

    ... FREQUENCY (GHz) Figure 17. Return Loss of HMPP-389T Mounted on Test Line at 0V and -20V Bias. Figure . Return loss of HMPP-389T mounted on test line at 0V and -0V bias. Normalization was used to remove the pcb’s and connec- tors’ losses from the measurement of the shunt switch’s loss ...

  • Page 10

    Assembly Information The MiniPak diode is mounted to the PCB or microstrip board using the pad pattern shown in Figure 26. 0.4 0.5 0.4 Figure 6. PCB Pad Layout, MiniPak (dimensions in mm). This mounting pad pattern is satisfactory for ...

  • Page 11

    ... MiniPak 141 Outline Drawing for HMPP-3890, -389, and -3895 1.44 (0.057) 1.40 (0.055) 1.20 (0.047) 1.16 (0.046) Top view 0.70 (0.028) 0.58 (0.023) Side view Dimensions are in millimeters (inches) MiniPak 141 Outline Drawing for HMPP-389T 0.92 (0.036) 0.00 0.88 (0.035) -0.07 (-0.003) ...

  • Page 12

    ... Ordering Information Part Number No. of Devices HMPP-389x-TR2 10000 HMPP-389x-TR1 3000 HMPP-389x-BLK 100 Device Orientation REEL USER FEED DIRECTION COVER TAPE 1 Container 13” Reel 7”Reel antistatic bag CARRIER TAPE 8 mm Note: “AA” represents package marking code. Package marking is right side up with carrier tape perforations at top. Conforms to Electronic Industries RS-481, “ ...

  • Page 13

    Tape Dimensions and Product Orientation For Outline 4T (MiniPak 141 / MiniPak QFN) For product information and a complete list of distributors, please go to our web site: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, ...