HTRC11001AD NXP Semiconductors, HTRC11001AD Datasheet

no-image

HTRC11001AD

Manufacturer Part Number
HTRC11001AD
Description
HITAG Reader Chip 14-Pin SO Tube
Manufacturer
NXP Semiconductors
Datasheet

Specifications of HTRC11001AD

Package
14SO
Power Supply Type
Analog
Typical Supply Current
4 mA
Typical Operating Supply Voltage
5 V
Minimum Operating Supply Voltage
4.5 V
Maximum Operating Supply Voltage
5.5 V
Product specification
Supersedes data of 1999 Jan 01
File under Integrated Circuits, IC11
DATA SHEET
HTRC11001T
HITAG reader chip
INTEGRATED CIRCUITS
2001 Nov 23

Related parts for HTRC11001AD

HTRC11001AD Summary of contents

Page 1

DATA SHEET HTRC11001T HITAG reader chip Product specification Supersedes data of 1999 Jan 01 File under Integrated Circuits, IC11 INTEGRATED CIRCUITS 2001 Nov 23 ...

Page 2

Philips Semiconductors HITAG reader chip CONTENTS 1 FEATURES 2 APPLICATIONS 3 GENERAL DESCRIPTION 4 QUICK REFERENCE DATA 5 ORDERING INFORMATION 6 BLOCK DIAGRAM 7 PINNING 8 FUNCTIONAL DESCRIPTION 8.1 Power supply 8.2 Antenna drivers 8.3 Diagnosis 8.4 Oscillator with programmable ...

Page 3

Philips Semiconductors HITAG reader chip 1 FEATURES Combines all analog RFID reader hardware in one single chip Optimized for HITAG transponder family Robust antenna coil power driver stage with modulator High performance adaptive sampling time AM/PM demodulator (patent pending) Read ...

Page 4

Philips Semiconductors HITAG reader chip 6 BLOCK DIAGRAM handbook, full pagewidth 4 TX1 ANTENNA 2 DRIVERS TX2 14 SYNCHRONOUS RX DEMODULATOR PHASE MEASUREMENT QGND 2001 Nov MODULATOR BANDPASS FILTER AMPLIFIER DYNAMIC CONTROL DIGITIZER ...

Page 5

Philips Semiconductors HITAG reader chip 7 PINNING SYMBOL PIN V 1 ground supply SS TX2 2 antenna driver output supply voltage (5 V stabilized) DD TX1 4 antenna driver output 1 MODE 5 control input to enable ...

Page 6

Philips Semiconductors HITAG reader chip 8 FUNCTIONAL DESCRIPTION 8.1 Power supply The HTRC11001T works with an external 5 V 10% power supply at pin V . The maximum DC current ...

Page 7

Philips Semiconductors HITAG reader chip 8.6 Idle and Power-down mode The HTRC11001T can be switched into the Idle mode via setting bit and resetting bit PD_MODE = 0 (see Table 3). In this Idle mode, only the ...

Page 8

Philips Semiconductors HITAG reader chip 8.8 Commands Table 1 Summary of the HTRC11001T command set BIT 7 BIT 6 COMMAND NAME MSB READ_TAG 1 WRITE_TAG_N 0 WRITE_TAG 1 READ_PHASE 0 0 SET_SAMPLING_TIME 1 GET_SAMPLING_TIME 0 0 SET_CONFIG_PAGE 0 GET_CONFIG_PAGE 0 ...

Page 9

Philips Semiconductors HITAG reader chip 8.8.3 C WRITE_TAG OMMAND NAME BIT 7 Command bits This is the 3-bit short form of the previously described command WRITE_TAG_N. It allows to switch into the WRITE_TAG mode with a minimum communication time. The ...

Page 10

Philips Semiconductors HITAG reader chip 8.8.7 C SET_CONFIG_PAGE OMMAND NAME BIT 7 Command This command is used to set the filter and amplifier parameters (cut-off frequencies and gain factors) and to select the operation mode. Bits P1 and P0 select ...

Page 11

Philips Semiconductors HITAG reader chip BIT NAME VALUE PD_MODE select Power-down mode 0 Idle mode 1 Power-down mode FREEZE1, facility to achieve fast settling times (MSB and LSB) FREEZE0 00 normal operation 01 main low-pass is frozen; main high-pass is ...

Page 12

Philips Semiconductors HITAG reader chip 8.8.8 C GET_CONFIG_PAGE OMMAND ? NAME BIT 7 Command bits Response bits This command has three functions: 1. Reading back the configuration parameters set by command SET_CONFIG_PAGE 2. Reading back the transmit pulse width programmed ...

Page 13

Philips Semiconductors HITAG reader chip 9 LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 60134); note 1. SYMBOL V voltage at any pin (except pin RX maximum voltage at any pin with respect to V ...

Page 14

Philips Semiconductors HITAG reader chip 11 AC CHARACTERISTICS +85 C. amb SYMBOL PARAMETER Oscillator inputs (pins XTAL1 and XTAL2) f oscillator frequency osc t start-up time st C input capacitance on pin XTAL1 i R input ...

Page 15

Philips Semiconductors HITAG reader chip 12 APPLICATION INFORMATION Figure 4 shows a minimal application circuitry for the HTRC11001T. The reader coil L together with the capacitor C a series resonant LC circuit (f = 125 kHz). The high 0 voltages ...

Page 16

Philips Semiconductors HITAG reader chip 13 PACKAGE OUTLINE SO14: plastic small outline package; 14 leads; body width 3 pin 1 index 1 e DIMENSIONS (inch dimensions are derived from the original mm dimensions) A UNIT A ...

Page 17

Philips Semiconductors HITAG reader chip 14 SOLDERING 14.1 Introduction to soldering surface mount packages This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our “Data Handbook IC26; ...

Page 18

Philips Semiconductors HITAG reader chip 14.5 Suitability of surface mount IC packages for wave and reflow soldering methods PACKAGE BGA, HBGA, LFBGA, SQFP, TFBGA HBCC, HLQFP, HSQFP, HSOP, HTQFP, HTSSOP, HVQFN, SMS (3) PLCC , SO, SOJ LQFP, QFP, TQFP ...

Page 19

Philips Semiconductors HITAG reader chip 15 DATA SHEET STATUS PRODUCT (1) DATA SHEET STATUS STATUS Objective data Development Preliminary data Qualification Product data Production Notes 1. Please consult the most recently issued data sheet before initiating or completing a design. ...

Page 20

Philips Semiconductors – a worldwide company Contact information For additional information please visit http://www.semiconductors.philips.com. For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com. © Koninklijke Philips Electronics N.V. 2001 All rights are reserved. Reproduction in whole or in part is prohibited ...

Related keywords