PTH05060WAH ARTESYN, PTH05060WAH Datasheet - Page 3

• Manufacturer Part Number: PTH05060WAH
• Description: Module DC-DC 1-OUT 0.8V to 3.6V 10A 36W 10-Pin Tray
• Manufacturer: ARTESYN
• Type: Step Downr

Specifications of PTH05060WAH

• Output Current: 10 A
• Output Voltage: 0.8 to 3.6 V
• Input Voltage: 5 V
• Number Of Outputs: 1
• Output Power: 36 W

Ordering Information
Output Power
(max)
Part Number System with Options
36 W
Output Voltage
Vo = 1.0 V
Vo = 1.2 V
Vo = 1.5 V
Vo = 1.8 V
Vo = 2.0 V
Vo = 2.5 V
Vo = 3.3 V
Efficiency Table
4.5 - 5.5 Vdc
Voltage
Input
Mechanical Package
Point of Load Alliance
(I O = 7 A)
Output Current
Product Family
0.8 - 3.6 Vdc
Input Voltage
Efficiency
Voltage
Output
The ultra-wide output voltage trim range offers major advantages to users who
select the PTH05060. It is no longer necessary to purchase a variety of modules in
order to cover different output voltages. The output voltage can be trimmed in a
range of 0.8 Vdc to 3.6 Vdc. When the PTH05060 converter leaves the factory the
output has been adjusted to the default voltage of 0.8 V.
Compatible
85%
86%
89%
90%
91%
92%
94%
06 = 10 A
Always 0
05 = 5 V
Output Voltage Adjustment of the PTH05060 Series
Output Currents
Min
0 A
P T H 0 5 0 6 0 W A S T
Max
10 A
Notes
1 Remote ON/OFF. Positive Logic
2 See Figures 1and 2 for safe operating curves.
3 A 330 µF electrolytic input capacitor is required for proper operation. The
4 An external output capacitor is not required for basic operation. Adding 330
5 1 A/µs load step, 50 to 100% I
6 If utilized Vout will track applied voltage by ±0.3 V (up to Vo set point).
7 The pre-bias start-up feature is not compatible with Auto-Track™. This is
8 Tape and reel packaging only available on the surface-mount versions.
9 To order Pb-free (RoHS compatible) surface-mount parts replace the
9 NOTICE: Some models do not support all options. Please contact your local
Efficiency
ON:
OFF:
capacitor must be rated for a minimum of 500 mA rms of ripple current.
µF of distributed capacitance at the load will improve the transient response.
because when the module is under Auto-Track™ control, it is fully active and
will sink current if the ouput voltage is below that of a back-feeding source.
Therefore to ensure a pre-bias hold-off, one of the following two techniques
must be followed when input power is first applied to the mdoule. The Auto-
Track™ function must either be disabled, or the module’s output held off
using the inhibit pin. Refer to Application Note 159 for more details.
mounting option ‘S’ with ‘Z’, e.g. PTH05060WAZ. To order Pb-free (RoHS
compatible) through-hole parts replace the mounting option ‘H’ with ‘D’, e.g.
PTH05060WAD.
Emerson Network Power representative or use the on-line model number search
tool at http://www.PowerConversion.com to find a suitable alternative.
(max)
94%
Pin 3 open; or V > Vin - 0.5 V
Pin 3 GND; or V < 0.8 V (min - 0.2 V).
± 10 mV
Line
Packaging Options
No Suffix = Trays
T = Tape and Reel
Pin Option
A = Through-Hole Std. Pin Length (0.140”)
A = Surface-Mount Tin/Lead Solder Ball
Output Voltage Code
W = Wide
Mounting Option
D = Horizontal Through-Hole (RoHS 6/6)
H = Horizontal Through-Hole (RoHS 5/6)
S = Surface-Mount Solder Ball (RoHS 5/6)
Z = Surface-Mount Solder Ball (RoHS 6/6)
Regulation
omax
, C
Embedded Power for
Business-Critical Continuity
± 12 mV
out
Load
= 330 µF.
(8)
(9)
Model Numbers
odel Numbers
PTH05060
PTH05060 Series
Rev. 3.23.09_71
(9, 10)
3 of 5