MMA02040E4701BB100 Vishay, MMA02040E4701BB100 Datasheet - Page 7

• Manufacturer Part Number: MMA02040E4701BB100
• Description: Res Thin Film 1406 4.7K Ohm 0.1% 1/4W ±15ppm/°C Molded Melf SMD Blister T/R
• Manufacturer: Vishay
• Type: Thin Filmr
• Series: MMAr

Specifications of MMA02040E4701BB100

• Case Size: 1406
• Resistance Value: 4.7 KOhm
• Power Rating: 1/4 W
• Tolerance: 0.1 %
• Metal Film: RESISTANCE
• Case Style: MMA0204
• Tolerance, +: 0.1%
• Tolerance, -: 0.1%
• Temp, Op. Max: 85(DEGREE C)
• Temp, Op. Min: -55(DEGREE
• Rohs Compliant: YES

www.vishay.com
40
MMU 0102, MMA 0204, MMB 0207 - Precision
Vishay Beyschlag
TESTS AND REQUIREMENTS
All tests are carried out in accordance with the following
specifications:
EN 60115-1, generic specification
EN 140400, sectional specification
EN 140401-803, detail specification
The components are approved in accordance with the
IECQ-CECC-system, where applicable. For the full test
schedule refer to the documents listed above. The testing
also covers most of the requirements specified by
EIA/IS-703 and JIS-C-5202.
The tests are carried out in accordance with IEC 60068* and
under standard atmospheric conditions in accordance with
IEC 60068-1, 5.3*. Climatic category LCT/UCT/56 (rated
temperature range: Lower Category Temperature, Upper
Category Temperature; damp heat, long term, 56 days) is valid.
CLAUSE
60115-1
TEST PROCEDURES AND REQUIREMENTS
4.5
4.8.4.2
4.25.1
4.25.3
4.24
4.39
EN
METHOD
60068-2*
-
-
-
-
78 (Cab)
67 (Cy)
TEST
IEC
resistance
temperature
coefficient
endurance at
70 °C: precision
operation mode
endurance at
70 °C: standard
operation mode
endurance at
upper category
damp heat,
steady state
damp heat,
steady state,
accelerated
TEST
For technical questions contact: [e-mail]
stability for product types:
-
at 20 / - 55 / 20 °C and
20 / 125 / 20 °C
U =
≤ U
1.5 h on; 0.5 h off;
70 °C; 1000 h
70 °C; 8000 h
U =
≤ U
1.5 h on; 0.5 h off;
70 °C; 1000 h
70 °C; 8000 h
85 °C; 1000 h
125 °C; 1000 h
(40 ± 2) °C; 56 days;
(93 ± 3) % RH
(85 ± 2) °C; (85 ± 5) % RH;
U = 0.1 ×
≤ 100 V;
1000 h
max
max
P
P
;
;
PROCEDURE
70
70
×
×
Precision MELF Resistors
P
R
R
70
×
R
MMU 0102
MMA 0204
MMB 0207
± (0.02 % R + 5 mΩ)
± (0.05 % R + 5 mΩ)
± (0.05 % R + 5 mΩ)
± (0.15 % R + 5 mΩ)
Unless otherwise specified the following values apply:
Temperature: 15 °C to 35 °C
Relative humidity: 45 % to 75 %
Air pressure: 86 kPa to 106 kPa (860 mbar to 1 060 mbar).
The components are mounted for testing on printed-circuit
boards in accordance with EN 140400, 2.3.3, unless
otherwise specified.
The
Requirements table are based on the required tests and
permitted limits of EN 140401-803. However, some
additional tests and a number of improvements against those
minimum requirements have been included. The stated
requirements for long-term tests are typically fulfilled with a
statistical safety of at least
100 Ω to 100 kΩ
100 Ω to 100 kΩ
100 Ω to 270 kΩ
OR BETTER
CLASS 0.05
STABILITY
requirements
± 0.5 % R; ± 0.25 % R; ± 0.1 % R
PERMISSIBLE CHANGE (ΔR)
± 25 ppm/K, ± 15 ppm/K
± (0.05 % R + 5 mΩ)
± (0.1 % R + 5 mΩ)
± (0.05 % R + 5 mΩ)
± (0.1 % R + 5 mΩ)
± (0.1 % R + 5 mΩ)
± (0.2 % R + 5 mΩ)
REQUIREMENTS
43 Ω to 147 kΩ
43 Ω to 221 kΩ
43 Ω to 510 kΩ
OR BETTER
stated
STABILITY
CLASS 0.1
x
+ 5 s.
± (0.25 % R + 5 mΩ)
± (0.1 % R + 5 mΩ)
in
Test
Document Number: 28714
± (0.15 % R + 5 mΩ)
± (0.1 % R + 5 mΩ)
Procedures
22 Ω to 332 kΩ
10 Ω to 511 kΩ
Revision: 18-Jul-06
OR BETTER
15 Ω to 1 MΩ
CLASS 0.25
STABILITY
and