B32592C1105K8 EPCOS Inc, B32592C1105K8 Datasheet
B32592C1105K8
Specifications of B32592C1105K8
Related parts for B32592C1105K8
B32592C1105K8 Summary of contents
Page 1
... Film Capacitors Metallized Polyester Film Capacitors (MKT) Series/Type: B32591 ... B32594 Date: May 2009 © EPCOS AG 2009. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. ...
Page 2
... High pulse strength High contact reliability Construction Dielectric: polyethylene terephthalate (polyester, PET) Stacked-film technology for lead spacing 10 and 15 mm (100 ... 400 V DC); Wound capacitor technology for lead spacing 10 and 15 mm (630 V DC) as well as for lead spacing 22.5 and 27.5 mm Epoxy resin coating (UL 94 V-0) ...
Page 3
... Technology Stacked-film technology / w = Wound capacitor technology Lead configurations Series Standard B32591 10 mm B32592 15 mm B32593 22.5 mm B32594 27.5 mm Please read Cautions and warnings and Important notes at the end of this document. ...
Page 4
... AC) 63 RMS 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 6.8 10 Technology Stacked-film technology / w = Wound capacitor technology Lead configurations Series Standard B32591 10 mm B32592 15 mm B32593 22.5 mm B32594 27.5 mm Please read Cautions and warnings and Important notes at the end of this document ...
Page 5
Ordering codes and packing units (lead spacing 10 mm Max. dimensions R RMS 100 63 0.10 5.0 0.15 5.0 0.22 5.0 0.33 5.5 0.47 6.0 0.68 ...
Page 6
B32592 General purpose (stacked/wound) Ordering codes and packing units (lead spacing 15 mm Max. dimensions R RMS 100 63 0.47 5.0 0.68 5.5 1.0 6.5 1.5 ...
Page 7
Ordering codes and packing units (lead spacing 22.5 mm Max. dimensions R RMS 100 63 1.5 7.0 2.2 8.5 3.3 10.0 4.7 11.5 6.8 13.0 250 ...
Page 8
B32594 General purpose (wound) Ordering codes and packing units (lead spacing 27.5 mm Max. dimensions R RMS 100 63 4.7 10.5 6.8 12.5 10 17.0 250 ...
Page 9
Technical data Operating temperature range Dissipation factor tan ( (upper limit values) Insulation resistance R ins or time constant = ins rel. humidity 65% (minimum as-delivered values) ...
Page 10
B32591 ... B32594 General purpose (stacked/wound) Pulse handling capability "dV/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal voltages, expressed "k " represents the maximum permissible pulse characteristic of the waveform applied to ...
Page 11
Impedance Z versus frequency f (typical values) Please read Cautions and warnings and Important notes at the end of this document. B32591 ... B32594 General purpose (stacked/wound) Page ...
Page 12
B32591 General purpose (stacked/wound) Permissible AC voltage V RMS For T >55 C, please refer to "General technical information", section 3.2.3. A Lead spacing 10 mm 100 V DC/ 400 V DC/200 V AC Please read Cautions and ...
Page 13
Permissible AC voltage V RMS For T >55 C, please refer to "General technical information", section 3.2.3. A Lead spacing 15 mm 100 V DC/ 400 V DC/200 V AC Please read Cautions and warnings and Important notes ...
Page 14
B32593 General purpose (wound) Permissible AC voltage V RMS For T >55 C, please refer to "General technical information", section 3.2.3. A Lead spacing 22.5 mm 100 V DC/ 400 V DC/200 V AC Please read Cautions and ...
Page 15
Permissible AC voltage V RMS For T >55 C, please refer to "General technical information", section 3.2.3. A Lead spacing 27.5 mm 100 V DC/ 400 V DC/200 V AC Please read Cautions and warnings and Important notes ...
Page 16
... Before a solderability test is carried out, terminals are subjected to accelerated ageing (to IEC 60068-2-2, test Ba exposure to dry heat at 155 C). Since the ageing temperature is far higher than the upper category temperature of the capacitors, the terminal wires should be cut off from the capacitor before the ageing procedure to prevent the solderability being impaired by the products of any capacitor decomposition that might occur ...
Page 17
... Important notes at the end of this document. General purpose (stacked/wound) 2.0 +0/ 0.5 mm from capacitor body or seating plane Heat-absorbing board, (1.5 0.5) mm thick, between capacitor body and liquid solder No visible damage 2% for MKT/MKP/MFP 5% for EMI suppression capacitors As specified in sectional specification Page B32591 ... B32594 ...
Page 18
... B32591 ... B32594 General purpose (stacked/wound) 1.3 General notes on soldering Permissible heat exposure loads on film capacitors are primarily characterized by the upper cate- gory temperature T . Long exposure to temperatures above this type-related temperature limit max can lead to changes in the plastic dielectric and thus change irreversibly a capacitor's electrical characteristics ...
Page 19
... MKT, MKP, MFP (coated/boxed) Even when suitable solvents are used, a reversible change of the electrical characteristics may occur in uncoated capacitors immediately after they are washed. Thus it is always recommended to dry the components (e. before they are subjected to subsequent electrical test- ing. Table A ...
Page 20
... B32591 ... B32594 General purpose (stacked/wound) 3 Embedding of capacitors in finished assemblies In many applications, finished circuit assemblies are embedded in plastic resins. In this case, both chemical and thermal influences of the embedding ("potting") and curing processes must be taken into account. Our experience has shown that the following potting materials can be recommended: non-flexible epoxy resins with acid-anhydride hardeners ...
Page 21
... IEC 60068-2-6. EPCOS offers film capacitors specially designed for operation under more severe vibration regimes such as those found in automotive applications. Consult our catalog "Film Capacitors for Automotive Electronics". Please read Cautions and warnings and Important notes at the end of this document. B32591 ... B32594 ...
Page 22
... Topic Safety information Soldering Do not exceed the specified time or temperature limits during soldering. Cleaning Use only suitable solvents for cleaning capacitors. 2 "Cleaning" Embedding of When embedding finished circuit assemblies in capacitors in plastic resins, chemical and thermal influences finished assemblies must be taken into account. ...
Page 23
Symbols and terms Symbol English Heat transfer coefficient Temperature coefficient of capacitance C A Capacitor surface area Humidity coefficient of capacitance C C Capacitance C Rated capacitance R C Absolute capacitance change C/C Relative capacitance change (relative deviation of actual ...
Page 24
B32591 ... B32594 General purpose (stacked/wound) Symbol English I (Sinusoidal) alternating current, RMS root-mean-square value i Capacitance drift z k Pulse characteristic 0 L Series inductance S Failure rate Constant failure rate during useful 0 service life Failure rate, determined ...
Page 25
Symbol English V Category voltage C V Category AC voltage C,RMS V Corona-discharge onset voltage CD V Charging voltage voltage DC V Fly-back capacitor voltage FB V Input voltage i V Output voltage o V Operating voltage ...
Page 26
Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical ...