91901-1 TE Connectivity, 91901-1 Datasheet

no-image

91901-1

Manufacturer Part Number
91901-1
Description
Connector Accessories Crimp Die For BNC Connector
Manufacturer
TE Connectivity
Type
Dier
Datasheets

Specifications of 91901-1

Rohs Compliant
NA
Cable Type
RG/U 55B
Lead Free Status / RoHS Status
RoHS Not Applicable
For Use With
BNC RG 55B
Lead Free Status / Rohs Status
RoHS Exempt Product
1. INTRODUCTION
SDE (Two-Piece) Crimping Die Assemblies are
designed to crimp a variety of connectors when used
in PRO-CRIMPER* III Frame Assembly 354940-1.
Refer to Figure 5 for a list of connectors and their
associated dies.
Catalog 1307191 provides a guide for cable-to-
connector selection. For connectors not referenced in
the catalog, contact Tyco Electronics Product
Engineering for recommendations.
Refer to instruction sheet 408-9930 for information
concerning PRO-CRIMPER II Hand Tool Frame
354940-1.
Reasons for reissue of this instruction sheet are
provided in Section 8, REVISION SUMMARY.
2. DESCRIPTION
Each two-piece crimping die assembly consists of an
indenter die and an anvil die, which when closed forms
two or three crimping chambers. The larger crimping
chambers crimp the ferrule of the connector onto the
coaxial cable. The smaller crimping chamber crimps
the center contact onto the center conductor of the
©2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company
All Rights Reserved
TE logo is a trademark.
*Trademark. Other products, logos, and company names might be trademarks of their respective owners.
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use
and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available.
Indenter
Die
Anvil Die
NOTE
i
Dimensions in this instruction sheet are in
millimeters [with inches in brackets]. Figures are for
reference only, and are not drawn to scale.
Figure 1
Center Contact
Crimping Chamber
SDE Crimping Die Assemblies
91900-1, 91901-1, 91903-1,
91904-[ ], and 91905-1
Ferrule
Crimping
Chamber
Typical
Crimpiing
Die Assembly
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752
coaxial cable. Each die is held in the PRO-CRIMPER
III hand tool jaws by a single screw. See Figure 1.
3. DIE INSTALLATION
4. CRIMPING PROCEDURE
Select the appropriate cable size and connector. The
wire size and insulation diameter must be within the
specified range for the connector.
For detailed information on cable strip lengths and
proper assembly of the connector, refer to the
instructions packaged with the connector. Make sure
that the connector's ferrule has been placed onto the
cable, and that the cable's braided shield is flared
away from the cable. Then proceed as follows:
4.1. Crimping the Center Contact
1. Close the tool handles until the ratchet releases,
then allow the tool handles to open fully.
2. Install anvil die in the movable jaw of the tool
frame. Align the die with the retaining screw hole,
then secure die with the die-retaining screw. Do
NOT fully tighten.
3. Install indenter die in the stationary jaw of the tool
frame. Slowly close the tool handles, allowing the
dies to align themselves.
4. Close the tool handles completely.
5. Securely tighten both screws with the appropriate
screwdriver.
1. Close the tool handles until the dies are partially
closed.
2. Assemble the center contact onto the cable
center conductor and place the center contact in the
smallest crimping chamber of the anvil die.
NOTE
NOTE
NOTE
i
i
i
Once the anvil has entered the indenter, place a
copper bus bar (1.57 ± 0.05 [.062 ± .002] diameter)
into the center contact crimping chamber of the die
assembly.
This tool is provided with a crimp height adjustment
feature. Initially, the crimp height should be verified.
Refer to Section 5, Crimp height Adjustment, to
verify crimp height before using the tool.
Make sure the flange on the end of the center
contact butts against the die.
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com
(Figure 1)
(Figure 2)
Instruction Sheet
408-8579
10 MAR 11 Rev C
1 of 5
LOC B

Related parts for 91901-1

91901-1 Summary of contents

Page 1

... SDE Crimping Die Assemblies 91900-1, 91901-1, 91903-1, 91904-[ ], and 91905-1 PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available. ...

Page 2

Crimping the Center Contact Anvil Die 3. Holding the cable in place, close the tool handles until the ratchet releases. 4. Allow the tool handles to open fully and remove the crimped center contact from the dies. 4.2. Crimping the ...

Page 3

... Figure 5 provides information on die opening sizes. Die assembly 91901-1 will require a center contact crimp height inspection using a micrometer with a with a modified anvil as shown in Figure 6. Tyco Electronics does not manufacture or market these gages ...

Page 4

... DESCRIPTION 91904-1 BNC COAXICON Connectors 91904-2 BNC COAXICON Connectors 91904-3 BNC COAXICON Connectors 91904-4 BNC COAXICON Connectors 91901-1 BNC COAXICON Connectors 91905-1 ARINC COAXICON Connectors 91903-1 50-Ohm C HN, N, and TNC COAXICON Connectors 91900-1 LFR Fiber Optic Connectors Rev C DIE CLOSURE DIMENSIONS ...

Page 5

... Tyco Electronics Representative, or call 1-800-526-5142, or send a facsimile of your purchase order to 1-717-986-7605, or write to: Rev C CUSTOMER SERVICE (038-035) TYCO ELECTRONICS CORPORATION PO BOX 3608 HARRISBURG PA 17105-3608 8. REVISION SUMMARY Since the previous release of these instructions, the TE Connectivity logo has been applied. Blade Spindle Anvil Figure 6 408-8579 ...

Related keywords