Conn Ejector Header HDR 16 POS 2.54mm Solder RA Thru-Hole

 

2-1761607-6

Manufacturer Part Number2-1761607-6
DescriptionConn Ejector Header HDR 16 POS 2.54mm Solder RA Thru-Hole
ManufacturerTE Connectivity
TypeEjector Header
SeriesAMP-LATCH
2-1761607-6 datasheet
 

Specifications of 2-1761607-6

Pitch2.54 mmNumber Of Rows2
Number Of Contacts16GenderHDR
Contact PlatingGold Over NickelTermination MethodSolder
Connector TypeWire To BoardContact TerminationRight Angle Through Hole
No. Of Contacts16No. Of Rows2
Pitch Spacing2.54mmConnectorRoHS Compliant
Product TypeHeaders - ShroudedNumber Of Positions / Contacts16
Mounting StyleThrough HoleMounting AngleRight
Termination StyleSolderHousing MaterialThermoplastic
Contact MaterialPhosphor BronzeProduct LineAMP-LATCH
ProfileLowPcb Mounting OrientationRight Angle
Pcb Mount RetentionWithoutMating Connector LockWithout
Housing Style4-SidedEjection LatchesWith
Post Size (mm [in])0.64 [.025]ShroudedYes
[shrouded] End Dimension (mm [in])3.81 [0.150]Termination Post Length (mm [in])2.60 [0.102]
Solder Tail Contact PlatingTin over NickelHeader TypePin Header
Number Of Positions16Centerline, Matrix (mm [in])2.54 x 2.54 [.100 x .100]
Daisy ChainWithPreloadedYes
Contact Plating, Mating Area, MaterialGold Flash over Palladium NickelContact ShapeSquare
Contact Base MaterialPhosphor BronzeConnector StyleHeader - Pin
Mating Alignment TypeCenter, MilitaryMating AlignmentWith
Ul Flammability RatingUL 94V-0Housing ColorBlue
Rohs/elv ComplianceRoHS compliant, ELV compliantLead Free Solder ProcessesWave solder capable to 240°C, Wave solder capable to 260°C, Wave solder capable to 265°C
Rohs/elv Compliance HistoryAlways was RoHS compliantTemperature RatingStandard
Lead Free Status / Rohs Status Details  
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
Page 1/5

Download datasheet (644Kb)Embed
Next
Product
Specification
AMP-LATCH* and IDC Header Connectors, .100 X .100 Inch Grid
1.
SCOPE
1.1.
Content
This specification covers perform ance, tests and quality requirem ents for AMP-LATCH* universal and
low profile, and IDC standard and low profile .100 X .100 inch grid headers, right angle and vertical
assem blies.
1.2.
Qualification
W hen tests are perform ed on subject product line, procedures specified in Figure 1 shall be used. All
inspections shall be perform ed using applicable inspection plan and product drawing.
1.3.
Successful qualification testing on the subject product line was com pleted on 03Nov95, additional
testing was com pleted on 23Feb10. The Qualification Test Report num ber for this testing is 501-325.
This docum entation is on file at and available from Engineering Practices and Standards (EPS).
2.
APPLICABLE DOCUM ENTS
The following docum ents form a part of this specification to the extent specified herein. Unless
otherwise specified, the latest edition of the docum ent applies. In the event of conflict between the
requirem ents of this specification and the product drawing, the product drawing shall take precedence.
In the event of conflict between the requirem ents of this specification and referenced docum ents, this
specification shall take precedence.
2.1.
TE Connectivity (TE) Docum ents
!
109-1: Test Specification (General Requirem ents for Test Specifications)
!
109 Series: Test Specifications as indicated in Figure 1
!
501-325: Qualification Test Report (Connector, AMPLATCH* Header, .100 X .100 Inch Grid)
2.2.
Industry Docum ent
EIA-364: Electrical Connector/Socket Test Procedures Including Environm ental Classifications
2.3.
Reference Docum ent
109-197: Test Specification (Tyco Electronics Test Specifications vs EIA and IEC Test Methods)
3.
REQUIREM ENTS
3.1.
Design and Construction
Product shall be of design, construction and physical dim ensions specified on applicable product
drawing.
3.2.
Materials
Materials used in the construction of this product shall be as specified on the applicable product
drawing.
©2011 Tyco Electronics Corporation,
| Indicates change
a TE Connectivity Ltd. Company
*Trademark
All Rights Reserved
TE logo is a trademark.
For latest revision, visit our website at www.te.com/documents.
For Regional Customer Service, visit our website at www.te.com
Other products, logos, and company names might be trademarks of their respective owners.
108-40018
11Mar11 Rev F
1 of 5
LOC B

2-1761607-6 Summary of contents

  • Page 1

    ... Successful qualification testing on the subject product line was com pleted on 03Nov95, additional testing was com pleted on 23Feb10. The Qualification Test Report num ber for this testing is 501-325. This docum entation is on file at and available from Engineering Practices and Standards (EPS). ...

  • Page 2

    ... Figure 1 (continued) 108-40018 Procedure Visual, dim ensional and functional per applicable quality inspection plan. EIA-364-21. 500 volts DC inute hold. Test between adjacent contacts of unm ated specim ens. EIA-364-20, Condition I. 1000 volts AC at sea level. Test between adjacent contacts of unm ated specim ens. ...

  • Page 3

    ... Test Description Therm al shock. Hum idity/tem perature cycling. Shall meet visual requirements, show no physical damage and shall meet requirements of NOTE additional tests as specified in Test Sequence in Figure 2. 3.6. Product Qualification and Requalification Test Sequence Exam ination of product Insulation resistance W ithstanding voltage Solderability ...

  • Page 4

    ... All test groups shall each consist inim headers of each type. B. Test Sequence Qualification inspection shall be verified by testing specim ens as specified in Figure 2. 4.2. Requalification Testing If changes significantly affecting form , fit or function are m ade to the product or m anufacturing process, product assurance shall coordinate requalification testing, consisting of all or part of the original testing sequence as determ ined by developm ent/product, quality and reliability engineering ...

  • Page 5

    AMP-LATCH Universal Header IDC Standard Profile Header Rev F AMP-LATCH Low Profile Header IDC Low Profile Header Figure 3 Contact Retention 108-40018 ...