MIC2027-2YWM Micrel Inc, MIC2027-2YWM Datasheet
MIC2027-2YWM
Specifications of MIC2027-2YWM
MIC2027-2YWM
Related parts for MIC2027-2YWM
MIC2027-2YWM Summary of contents
Page 1
... A fault status output flag is asserted during overcurrent and thermal shutdown conditions. Transient current limit faults are internally filtered. The MIC2027/77 are available in 16-pin narrow (150 mil) and wide (300 mil) SOIC packages. Data sheets and support documentation can be found on Micrel’s web site at www.micrel.com. ...
Page 2
... Micrel, Inc. (1) Ordering Information Part Number Standard Pb-Free MIC2027-1BWM MIC2027-1YWM MIC2027-1BM MIC2027-1YM MIC2027-2BWM MIC2027-2YWM MIC2027-2BM MIC2027-2YM MIC2077-1BWM MIC2077-1YWM MIC2077-1BM MIC2077-1YM MIC2077-2BWM MIC2077-2YWM MIC2077-2BM MIC2077-2YM Pin Configuration 16-Pin SOIC (M) 16-Pin Wide SOIC (WM) September 2006 Enable Temperature Range Active High –40°C to +85°C Active High – ...
Page 3
... Input: Channel C and D switch and logic supply input. Switch C Output Switch C Enable (Input) Fault Flag C (Output) Fault Flag D (Output) Switch D Enable (Input) Switch D Output Supply Input: Channel A and B switch and logic supply input. Switch B Output Switch B Enable (Input) Fault Flag B (Output) 3 MIC2027/2077 to assert flag. D M9999-091506 ...
Page 4
... OUT OUT LIMIT (short applied to output 5V, apply until FLG low IN OUT V = 3.3V, apply until FLG low IN OUT 4 MIC2027/2077 (2) ) ..................................... +2.7V to +5. .......................... –40°C to +85° ..................... Internally Limited J )................................120°C/W JA ).........................................112°C ..........................................................130°C/W JA Min Typ Max 1.5 1.5 ...
Page 5
... 10mA 10mA 3. FLAG T increasing, each switch J T decreasing, each switch J T increasing, both switches J T decreasing, both switches J 5 MIC2027/2077 Min Typ Max Units 2.2 2.4 2.7 V 2.0 2.15 2.5 V Ω Ω µA 140 °C 120 °C 160 °C 150 ° ...
Page 6
... Micrel, Inc. Test Circuit Timing Diagrams September 2006 Output Rise and Fall Times Active-Low Switch Delay Times (MIC20x7-2) Active-High Switch Delay Times (MIC20x7-1) 6 MIC2027/2077 M9999-091506 ...
Page 7
... Micrel, Inc. Typical Characteristics September 2006 7 MIC2027/2077 M9999-091506 ...
Page 8
... Micrel, Inc. Typical Characteristics (cont.) September 2006 8 MIC2027/2077 M9999-091506 ...
Page 9
... Micrel, Inc. Functional Characteristics September 2006 9 MIC2027/2077 M9999-091506 ...
Page 10
... Micrel, Inc. Functional Characteristics (cont.) September 2006 10 MIC2027/2077 M9999-091506 ...
Page 11
... Micrel, Inc. Functional Characteristics (cont.) September 2006 11 MIC2027/2077 M9999-091506 ...
Page 12
... Micrel, Inc. Block Diagram September 2006 12 MIC2027/2077 M9999-091506 ...
Page 13
... Toggling EN will also reset the latch. The MIC2027 will automatically reset its output when the die temperature cools down to 120°C. The MIC2027 output and FLG signal will continue to cycle on and off until the device is disabled or the fault is removed ...
Page 14
... Micrel, Inc. Figure 1. MIC2077-2 Fault Timing: Output Reset by Removing Load OUT I LIMIT I LOAD I OUT V FLG September 2006 Short-Circuit Fault Load/Fault Removed Thermal Shutdown Reached 3ms typ. delay Figure 2. MIC2207-2 Fault Timing 14 MIC2027/2077 M9999-091506 ...
Page 15
... Printed Circuit Board Hot-Plug The MIC2027/77 are ideal inrush current-limiters for hot- plug applications. Due to the integrated charge pump, the MIC2027/77 present a high impedance when off and slowly becomes a low impedance as it turns on. This “soft-start” feature effectively isolates power supplies from highly capacitive loads by reducing inrush current. In cases of extremely large capacitive loads (> ...
Page 16
... Micrel, Inc. Package Information September 2006 16-Pin SOIC (M) 16 MIC2027/2077 M9999-091506 ...
Page 17
... Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully September 2006 16-Pin Wide SOIC (WM) indemnify Micrel for any damages resulting from such use or sale. © 2001 Micrel, Incorporated. 17 MIC2027/2077 M9999-091506 ...