PIC16F1829-E/P Microchip Technology, PIC16F1829-E/P Datasheet - Page 235

• Manufacturer Part Number: PIC16F1829-E/P
• Description: 14 KB Flash, 1K Bytes RAM, 32 MHz Int. Osc, 18 I/0, Enhanced Mid Range Core 20 P
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ mTouch™ 16Fr

Specifications of PIC16F1829-E/P

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 32MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 17
• Program Memory Size: 14KB (8K x 14)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: *
• Processor Series: PIC16F182x
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 18
• Number Of Timers: 5
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: Through Hole
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

24.4.6
In Single Output mode, PWM steering allows any of the
PWM pins to be the modulated signal. Additionally, the
same PWM signal can be simultaneously available on
multiple pins.
Once
(CCPxM<3:2> = 11
CCPxCON register), the user firmware can bring out
the same PWM signal to one, two, three or four output
pins by setting the appropriate STRx<D:A> bits of the
PSTRxCON register, as shown in
While the PWM Steering mode is active, CCPxM<1:0>
bits of the CCPxCON register select the PWM output
polarity for the Px<D:A> pins.
The PWM auto-shutdown operation also applies to
PWM Steering mode as described in
“Enhanced PWM Auto-shutdown
shutdown event will only affect pins that have PWM
outputs enabled.
FIGURE 24-18:
 2010 Microchip Technology Inc.
Note 1: Port outputs are configured as shown when
Note:
PORT Data
PORT Data
PORT Data
PORT Data
PxA Signal
CCPxM0
CCPxM1
CCPxM0
2: Single PWM output requires setting at least
CCPxM1
the
STRxA
STRxB
STRxC
STRxD
the CCPxCON register bits PxM<1:0> = 00
and CCPxM<3:2> = 11.
one of the STRx bits.
PWM STEERING MODE
The associated TRIS bits must be set to
output (‘0’) to enable the pin output driver
in order to see the PWM signal on the pin.
Single
and
SIMPLIFIED STEERING
BLOCK DIAGRAM
Output
1
0
1
0
1
0
1
0
PxM<1:0> = 00
mode
Table
TRIS
TRIS
TRIS
TRIS
mode”. An auto-
Section 24.4.3
24-8.
PxB pin
PxC pin
PxD pin
is
PxA pin
selected
of
Preliminary
the
PIC16F/LF1825/1829
DS41440A-page 237