PIC16F1829-E/P Microchip Technology, PIC16F1829-E/P Datasheet - Page 92

• Manufacturer Part Number: PIC16F1829-E/P
• Description: 14 KB Flash, 1K Bytes RAM, 32 MHz Int. Osc, 18 I/0, Enhanced Mid Range Core 20 P
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ mTouch™ 16Fr

Specifications of PIC16F1829-E/P

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 32MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 17
• Program Memory Size: 14KB (8K x 14)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: *
• Processor Series: PIC16F182x
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 18
• Number Of Timers: 5
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: Through Hole
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIC16F/LF1825/1829
8.3
Some interrupts can be used to wake from Sleep. To
wake from Sleep, the peripheral must be able to
operate without the system clock. The interrupt source
must have the appropriate Interrupt Enable bit(s) set
prior to entering Sleep.
On waking from Sleep, if the GIE bit is also set, the
processor will branch to the interrupt vector. Otherwise,
the processor will continue executing instructions after
the SLEEP instruction. The instruction directly after the
SLEEP instruction will always be executed before
branching to the ISR. Refer to the
Down Mode (Sleep)”
8.4
The INT pin can be used to generate an asynchronous
edge-triggered interrupt. This interrupt is enabled by
setting the INTE bit of the INTCON register. The
INTEDG bit of the OPTION register determines on which
edge the interrupt will occur. When the INTEDG bit is
set, the rising edge will cause the interrupt. When the
INTEDG bit is clear, the falling edge will cause the
interrupt. The INTF bit of the INTCON register will be set
when a valid edge appears on the INT pin. If the GIE and
INTE bits are also set, the processor will redirect
program execution to the interrupt vector.
8.5
Upon entering an interrupt, the return PC address is
saved on the stack. Additionally, the following registers
are automatically saved in the Shadow registers:
• W register
• STATUS register (except for TO and PD)
• BSR register
• FSR registers
• PCLATH register
Upon exiting the Interrupt Service Routine, these regis-
ters are automatically restored. Any modifications to
these registers during the ISR will be lost. If modifica-
tions to any of these registers are desired, the corre-
sponding Shadow register should be modified and the
value will be restored when exiting the ISR. The
Shadow registers are available in Bank 31 and are
readable and writable. Depending on the user’s appli-
cation, other registers may also need to be saved.
DS41440A-page 92
Interrupts During Sleep
INT Pin
Automatic Context Saving
for more details.
Section 9.0 “Power-
Preliminary
 2010 Microchip Technology Inc.