PIC24HJ64GP510A-E/PF Microchip Technology, PIC24HJ64GP510A-E/PF Datasheet - Page 157

• Manufacturer Part Number: PIC24HJ64GP510A-E/PF
• Description: 16 Bit MCU 40MIPS 64KB FLASH 100 TQFP 14x14x1mm TRAY
• Manufacturer: Microchip Technology
• Series: PIC® 24Hr

Specifications of PIC24HJ64GP510A-E/PF

• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 64KB (22K x 24)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 32x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 100-TQFP, 100-VQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

15.0
FIGURE 15-1:
 2009 Microchip Technology Inc.
Note 1: This data sheet summarizes the features
Note 1:
2: Some registers and associated bits
OUTPUT COMPARE
of the PIC24HJXXXGPX06A/X08A/X10A
families of devices. It is not intended to be
a comprehensive reference source. To
complement the information in this data
sheet, refer to the “dsPIC33F/PIC24H
Family Reference Manual”, Section 13.
“Output Compare” (DS70247), which is
available on the Microchip web site
(www.microchip.com).
described in this section may not be avail-
able on all devices. Refer to Section 4.0
“Memory Organization” in this data
sheet for device-specific register and bit
information.
2: The OCFA pin controls OC1 through OC4. The OCFB pin controls OC5 through OC8.
An ‘x’ in a signal, register or bit name denotes the number of the output compare channels.
OUTPUT COMPARE MODULE BLOCK DIAGRAM
16
TMR2
OCxRS
Comparator
OCxR
0
PIC24HJXXXGPX06A/X08A/X10A
TMR3
(1)
(1)
1
16
OCTSEL
Rollover Rollover
Preliminary
TMR2
0
TMR3
1
The output compare module can select either Timer2 or
Timer3 for its time base. The module compares the
value of the timer with the value of one or two Compare
registers depending on the operating mode selected.
The state of the output pin changes when the timer
value matches the Compare register value. The output
compare module generates either a single output
pulse, or a sequence of output pulses, by changing the
state of the output pin on the compare match events.
The output compare module can also generate inter-
rupts on compare match events.
The output compare module has multiple operating
modes:
• Active-Low One-Shot mode
• Active-High One-Shot mode
• Toggle mode
• Delayed One-Shot mode
• Continuous Pulse mode
• PWM mode without Fault Protection
• PWM mode with Fault Protection
Mode Select
OCM<2:0>
Output
Logic
3
Set Flag bit
OCxIF
(1)
R
S
Q
Output Enable
DS70592B-page 157
OCx
OCFA
or
OCFB
(1)
(2)