M27C800-100F1 STMicroelectronics, M27C800-100F1 Datasheet
M27C800-100F1
Specifications of M27C800-100F1
Available stocks
Related parts for M27C800-100F1
M27C800-100F1 Summary of contents
Page 1
... ELECTRONIC SIGNATURE – Manufacturer Code: 20h – Device Code: B2h DESCRIPTION The M27C800 Mbit EPROM offered in the two ranges UV (ultra violet erase) and OTP (one time programmable ideally suited for micro- processor systems requiring large data or program storage organised as either 1 Mwords of 8 bit or 512 Kwords of 16 bit ...
Page 2
... CC 31 Q15A– Q14 Q13 Q12 M27C800 34 23 Address Inputs Data Outputs Data Outputs Data Output / Address Input Chip Enable Output Enable Byte Mode / Program Supply PP Supply Voltage Ground Not Connected Internally A12 A13 A14 A15 A16 BYTEV Q15A–1 Q7 Q14 Q6 ...
Page 3
... Data Out Data Out Hi-Z Hi-Z Hi-Z Hi-Z Code Codes ID Q11 Q10 Q9 Q8 and and and and M27C800 Unit °C °C ° Q7-Q0 Data Out Data Out Data Out Hi-Z Data In Data Out Hi-Z Hi-Z Codes Hex Data 20h B2h 3/18 ...
Page 4
... High Speed 3V 0V Standard 2.4V 0.4V DEVICE OPERATION The operating modes of the M27C800 are listed in the Operating Modes Table. A single power supply is required in the read mode. All inputs are TTL compatible except for V and 12V on A9 for the PP Electronic Signature. Read Mode The M27C800 has two organisations, Word-wide and Byte-wide ...
Page 5
... OUT > 2.1mA –400µA OH and removed simultaneously or after 0.5V. CC M27C800 is placed in the standby mode by apply- ing a CMOS high signal to the E input. When in the standby mode, the outputs are in a high imped- ance state, independent of the G input. Min Max = 120 ...
Page 6
... V CC Test Condition -50 Min and removed simultaneously or after ± ± 10 Parameter Test Condition and removed simultaneously or after M27C800 (3) -70 -90 Max Min Max Min Max PP M27C800 -100 -120/150 Min Max Min Max , 100 120 100 120 IL IL 100 120 PP. Unit Unit ...
Page 7
... V V for every eight devices. This capacitor should SS be mounted near the power supply connection point. The purpose of this capacitor is to overcome the voltage drop caused by the inductive effects of PCB traces. M27C800 VALID tAXQX tEHQZ tGHQZ Hi-Z AI01596B and V ...
Page 8
... M27C800 Figure 6. Byte-Wide Read Mode AC Waveforms A–1,A0-A18 E G Q0-Q7 Note: BYTEV = V PP IL. Figure 7. BYTE Transition AC Waveforms A0-A18 A–1 BYTEV PP Q0-Q7 Q8-Q15 Note: Chip Enable (E) and Output Enable ( 8/18 VALID tAVQV tGLQV tELQV VALID VALID tAVQV tBLQX Hi-Z tBLQZ . IL VALID tAXQX tEHQZ ...
Page 9
... Sampled only, not 100% tested. Programming When delivered (and after each erasure for UV EPROM), all bits of the M27C800 are in the '1' state. Data is introduced by selectively program- ming '0's into the desired bit locations. Although only '0's will be programmed, both '1's and '0's can be present in the data word ...
Page 10
... Ex- cept for E, all like inputs including G of the parallel M27C800 may be common. A TTL low level pulse applied to a M27C800's E input and V will program that M27C800. A high level E input in- hibits the other M27C800s from being pro- grammed. Program Verify ...
Page 11
... M27C800 in about 3 years, while it would take approximately 1 week to cause erasure when exposed to direct sunlight. If the M27C800 exposed to these types of lighting conditions for extended periods of time suggested that opaque labels be put over to V ...
Page 12
... Options TR = Tape & Reel Packing Note: 1. High Speed, see AC Characteristics section for further information. For a list of available options (Speed, Package, etc...) or for further information on any aspect of this de- vice, please contact the STMicroelectronics Sales Office nearest to you. 12/18 M27C800 - ...
Page 13
... Table 1. Revision History Date March 1999 First Issue 50ns speed class addes (Tables 8A and 11) 25-Jan-2000 Electronic Signature change (Table 4) FDIP42W Package Dimension, L Max added (Table 12) 25-Sep-2000 AN620 Reference removed 10-Dec-2001 Ordering Information Scheme (Table 11) clarified Revision Details M27C800 13/18 ...
Page 14
... M27C800 Table 12. FDIP42W - 42 pin Ceramic Frit-seal DIP, with window, Package Mechanical Data Symbol Typ 1. 50.80 E 15. 2.54 eA 14. 9.40 K1 11.43 N Figure 10. FDIP42W - 42 pin Ceramic Frit-seal DIP, with window, Package Outline Drawing is not to scale. 14/18 millimeters Min Max 5.72 0.51 1.40 3.91 4 ...
Page 15
... M27C800 inches Typ Min – 0.010 0.140 0.015 0.050 0.008 2.055 2.000 – 0.600 – 0.535 0.100 – 0.590 – 0.600 0.125 0.034 0° ...
Page 16
... M27C800 Table 14. PLCC44 - 44 lead Plastic Leaded Chip Carrier, Package Mechanical Data Symbol Typ 1. 0. Figure 12. PLCC44 - 44 lead Plastic Leaded Chip Carrier, Package Outline PLCC Drawing is not to scale. 16/18 millimeters Min Max 4.20 4.70 2.29 3.04 – 0.51 0.33 0.53 0.66 0.81 17 ...
Page 17
... M27C800 inches Typ Min 0.095 0.009 0.089 0.004 1.106 0.520 0.050 – 0.626 0.031 – 3° – Max 0.103 0.010 0.093 0.020 ...
Page 18
... M27C800 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice ...