MT29F8G08ABABAWP:B Micron Technology Inc, MT29F8G08ABABAWP:B Datasheet - Page 83

no-image

MT29F8G08ABABAWP:B

Manufacturer Part Number
MT29F8G08ABABAWP:B
Description
Manufacturer
Micron Technology Inc
Datasheet

Specifications of MT29F8G08ABABAWP:B

Lead Free Status / RoHS Status
Supplier Unconfirmed

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MT29F8G08ABABAWP:B
Manufacturer:
SPANSION
Quantity:
4 310
Part Number:
MT29F8G08ABABAWP:B
Manufacturer:
MICRON
Quantity:
11 200
Part Number:
MT29F8G08ABABAWP:B
Manufacturer:
MICRON
Quantity:
4 000
Part Number:
MT29F8G08ABABAWP:B
Manufacturer:
MICRON/美光
Quantity:
20 000
Part Number:
MT29F8G08ABABAWP:B
Manufacturer:
MICRON
Quantity:
15 146
Company:
Part Number:
MT29F8G08ABABAWP:B
Quantity:
3 500
PROGRAM OTP PAGE (80h–10h)
Figure 57:
PDF: 09005aef8386131b / Source: 09005aef838cad98
m61a_async_sync_nand.fm - Rev. A 2/09 EN
Cycle type
(DQ[7:0])
I/O[7:0]
R/B#
Command
80h
PROGRAM OTP PAGE (80h–10h) Operation
Address
C1
Address
The PROGRAM OTP PAGE (80h-10h) command is used to write data to the pages within
the OTP area. An entire page is programmed at one time. To program data in the OTP
area, the device must be in OTP operating mode.
To use the PROGRAM PAGE command, issue the 80h command. Issue 5 address cycles:
the first 2 address cycles are the column address, and for the remaining 3 cycles, select a
page in the range of 02h-00h-00h through 1Fh-00h-00h. Next, write the data to the cache
register using data input cycles. After data input is complete, issue the 10h command.
R/B# goes LOW for the duration of the array programming time,
STATUS (70h) command is the only valid command for reading status in OTP operation
mode. The RDY bit of the status register will reflect the state of R/B#. Use of the SELECT
LUN WITH STATUS (78h) command is prohibited.
When the device is ready, read the FAIL bit of the status register to determine if the oper-
ation passed or failed (see Table 14 on page 56).
The PROGRAM OTP PAGE (80h-10h) command also accepts the CHANGE WRITE
COLUMN (85h) command during data input.
If a PROGRAM PAGE command is issued to the OTP area after the area has been
protected, R/B# goes LOW for
It is possible to program each OTP page a maximum of 8 times.
C2
OTP Page
Address
Address
00h
Micron Confidential and Proprietary
Address
8Gb Asychronous/Synchronous NAND Flash Memory
00h
t ADL
83
D
D1
t
OBSY. After
IN
D
IN
Micron Technology, Inc., reserves the right to change products or specifications without notice.
t
D
Dn
OBSY, the status register is set to 60h.
IN
Command
10h
t WB
t PROG
Command Definitions
©2008 Micron Technology, Inc. All rights reserved.
t
PROG. The READ
Command
70h
t WHR
Status
D
OUT
Advance

Related parts for MT29F8G08ABABAWP:B