BTS3408GXT Infineon Technologies, BTS3408GXT Datasheet
BTS3408GXT
Specifications of BTS3408GXT
Related parts for BTS3408GXT
BTS3408GXT Summary of contents
Page 1
... Line, stepper motor, lamp and relay driver General Description The BTS3408G is a dual channel Low-Side Switch with D-MOS output stages for driving resistive, capacitive and inductive loads. The design is based on Infineons Smart Power Technology (SPT) which allows bipolar, CMOS and power D-MOS devices on the same monolithic circuit ...
Page 2
Product Summary Parameter Supply voltage Continuous drain source voltage On-state resistance Current limitation Nominal output current (individual channel) Clamping energy BTS 3408 FAULT IN1 IN2 ENA Figure 1 Block Diagram Figure 2 Pin Configuration Datasheet Rev. 1.3 Symbol V S ...
Page 3
Pin Definitions and Functions Pin Symbol Function 1 FAULT General Fault Flag; see Table 2 for operation mode. 2 IN1 Input 1; input of channel 1; has an internal pull down; TTL/ CMOS compatible input. 3 IN2 Input 2; input ...
Page 4
... The ENA/FREEZE input can be used to enable and/or to freeze the output control of the cut off the complete IC. By pulling the ENA input to low, i.e. applying a Voltage V The power stages are switched off and the current consumption is reduced applying a Voltage V ENAFZ in their former state. All input signals will be ignored. ...
Page 5
... PWM-mode (selective thermal shutdown with restart) to prevent critical chip temperatures. The temperature hysteresis is typically 10K. Zener clamping is implemented to limit voltages at the power transistors when inductive loads are switched off. Diagnostic The general FAULT pin is an open drain output. The FAULT pin is low active. It signals fault conditions of any of the two output stages ...
Page 6
Absolute Maximum Ratings T = -40°C to 150°C , unless otherwise specified j Parameter Supply Voltage Drain source voltage (OUT1, OUT2) Input voltage (IN1, IN2, ENA) Continuous input current V FAULT output voltage Operating temperature range Storage temperature range 2) ...
Page 7
Electrical Characteristics 4.5 to 18V; = -40 to 150°C; unless otherwise specified S j Parameter Power supply Supply voltage Supply current in enable mode Supply current in standby mode Power outputs Drain source clamp voltage 2) Output ...
Page 8
Electrical Characteristics (cont’ 4.5 to 18V; = -40 to 150°C; unless otherwise specified S j Parameter Input ’High’ voltage IN1, IN2: ENA: Input voltage hysteresis Input pull down current IN1, IN2: ENA: Digital Output (FAULT) Output ’Low’ ...
Page 9
EMC-Characteristics The following EMC-Characteristics outline the behavior of typical devices. They are not part of any production test. Table 3 Test Conditions Parameter Temperature Supply Voltage Input Voltage (ENA, IN1, IN2) Load Operation mode DUT specific Fast electrical transients acc. ...
Page 10
Figure 3 Test circuit for ISO pulse PULSE V BB stress also for V S 13.5V 3408 VS FAULT OUT1 IN1 IN2 OUT2 ENA GND Datasheet Rev. 1 HITFET BTS3408G 2008-01-09 ...
Page 11
Conducted Emissions Acc. IEC 61967-4 (1Ω/150Ω method) Typ. OUT Emissions at PWM-mode x with 150Ω-matching network 100 -10 -20 0 MHz Figure 4 Test circuit for ...
Page 12
Terms FLT V FLT I IN1 V I IN1 IN2 V I IN2 ENA V ENA Figure 6 Input circuit (ESD protection) ESD zener diodes are not designed for DC current. Figure 7 Inductive and over voltage ...
Page 13
... Timing diagrams Figure 9 Switching a resistive load ENA DSx 0.9 Figure 10 Switching an inductive load ENA DSx Figure 11 Short circuit ENA ϑ jx FAULT Datasheet Rev. 1.3 Characteristics 1. Max. allowable Power Dissipation P = tot 0.1 off DS(AZ) 2. On-state Resistance Ω thermal hysteresis HITFET ...
Page 14
Typ. Short Circuit Current D(lim (lim ) typ . Typ. Supply current in ...
Page 15
Datasheet Rev. 1.3 HITFET 15 BTS3408G 2008-01-09 ...
Page 16
Package Outline 1.27 +0.1 2) 0.41 -0. -0.2 Index Marking 1) Does not include plastic or metal protrusion of 0.15 max. per side 2) Lead width can be 0.61 max. in dambar area PG-DSO8-36 ...
Page 17
Revision History Version Date Rev. 1.3 2008-01-09 Changed package outline drawing, updated package name Rev. 1.2 2007-06-15 Released automotive green version Rev. 1.1 2005-10-10 Released production version Datasheet Rev. 1.3 Changes Package parameter (humidity and climatic) removed in Maximum ratings ...
Page 18
... Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life ...