BTS723GWXT Infineon Technologies, BTS723GWXT Datasheet

Page 1

... Data Sheet Smart High-Side Power Switch Ω Ω Ω  Block Diagram 1 BTS723GW  Package P-DSO-14 PG-DSO14 V1.1, 2007-09-25 ...

Page 2

... Data Sheet Smart High-Side Power Switch  2 BTS723GW V1.1, 2007-09-25 ...

Page 3

... Diagnostic feedback 1,2 of channel 1,2 open drain 5 ST2 4 GND Logic Ground Connection for external pull up voltage source 11 SPU for the open drain status output. Pull up resistors are integrated. Data Sheet Smart High-Side Power Switch Pin configuration (top view IN1 2 ST1 3 GND 4 ST2 ...

Page 4

... V Load dump protection LoadDump = 8 Ω 200 ms low or high each channel loaded with R Operating temperature range Storage temperature range Power dissipation (DC) 5) (all channels active) Maximal switchable inductance, single pulse = 12V 150°C j,start bb = 110 mJ, 0 Ω 2 278 mJ, 0 Ω 3 see diagrams on page 12 Electrostatic discharge capability (ESD): (Human Body Model) acc ...

Page 5

... Electrical Characteristics Parameter and Conditions -40...+150° unless otherwise specified j bb Load Switching Capabilities and Characteristics On-state resistance ( OUT); each channel, two parallel channels, T see diagram, page Soldering point: Upper side of solder edge of device pin 15. See page 15 Data Sheet ...

Page 6

... V bb require an external current limit for the GND; a 150Ω resistor is bb(AZ) in table of protection functions and circuit diagram on page 10. 6 Smart High-Side Power Switch BTS723GW Values min typ Max 2.5 2 ...

Page 7

... In case of an inverse current of 3A the both status outputs must not be disturbed. 20 The neighbour channel can be switched normally; not all paramters lay within the range of the spec Please note, that in case of an inverse current no protection function is active. The power dissipation is ...

Page 8

... L(off) V OUT(OL ON(SC Input Status ST R Status pull up pull up V IN(T+) V IN(T-) ∆ 0 IN(off IN(on) V ST(high 5V: ST(low) SPU 8 Smart High-Side Power Switch BTS723GW Values min typ Max -- 3 2.0 2.85 3 0.53 0.85 1 1.2 -- 2.2 1 0.25 IN( 5.4 6 0.4 V1.1, 2007-09-25 Unit µA ...

Page 9

... GND H Short circuit Overtem- L perature H Parallel switching of channel 1 and 2 is easily possible by connecting the inputs and outputs in parallel. In this mode it is recommended to use only one status. Terms Leadframe ( connected to pin 1,7,8,14 bb External R optional; a single resistor R GND operating voltage. Data Sheet Status 1 ...

Page 10

... ST pull up The use of ESD zener diodes as voltage clamp at DC conditions is not recommended Short Circuit detection Fault Signal at ST-Pin: V > 4.0 V typ, no switch off by ON the PROFET itself, external switch off recommended! Data Sheet Inductive and overvoltage output clamp, IN1 or IN2 OUT1 or OUT2 ...

Page 11

... For inductive load currents up to the limits defined by Z (max. ratings and diagram on page 12) each switch is protected against loss Consider at your PCB layout that in the case of Vbb dis- connection with energized inductive load all the load current flows through the GND connection ...

Page 12

... Maximum allowable load inductance for a single switch off (one channel j,start = 150° Ω [mH] Data Sheet Typ. on-state resistance [mOhm · i (t) dt, ON(CL) L · ( OUT(CL) Typ. standby current , EERII 5) I bb(off [A] 12 Smart High-Side Power Switch = high ; 9...34 V, IN1,2,3,4 = low bb [µA] V1.1, 2007-09-25 BTS723GW V [ [°C] j ...

Page 13

... Figure 1a: V turn on case of too early V IN =high the device may not turn on (curve A) approx. 150 µs t d(bb IN) Figure 2a: Switching a resistive load, turn-on/off time and slew rate definition: on Data Sheet Figure 2b: Switching an inductive load Figure 3a: Short circuit: shut down by overtempertature, reset by cooling ...

Page 14

... Figure 4a: Overtemperature: Reset if T < Figure 5a: Open load, : detection in OFF-state, open load occurs in off-state = 2 µA typ > 2.7V L OUT Data Sheet Smart High-Side Power Switch Figure 6: Overvoltage, no shutdown ON(CL) V OUT(OL) 14 BTS723GW V1.1, 2007-09-25 ...

Page 15

... A B 14x 8.75 -0.2 A Index Marking 1) Does not include plastic or metal protrusion of 0.15 max. per side 2) Lead width can be 0.61 max. in dambar area 15 Smart High-Side Power Switch 0.35 x 45˚ 0.64 ±0.25 6 ±0.2 0 GPS01230 Dimensions in mm V1.1, 2007-09-25 BTS723GW ...

Page 16

... Creation of the green datasheet. First page : Adding the green logo and the AEC qualified Adding the bullet AEC qualified and the RoHS compliant features Package page : Modification of the package to be green. Data Sheet Smart High-Side Power Switch 16 BTS723GW V1.1, 2007-09-25 ...

Page 17

... Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body support and/or maintain and sustain and/or protect human life ...