ICE2PCS01GXT

Manufacturer Part NumberICE2PCS01GXT
ManufacturerInfineon Technologies
ICE2PCS01GXT datasheet
 


Specifications of ICE2PCS01GXT

Start-up Supply Current300uASwitching Freq50 to 315KHz
Operating Supply Voltage (min)10.4VOperating Supply Voltage (max)25V
Operating Temp Range-40C to 125COperating Temperature ClassificationAutomotive
Package TypeDSOPin Count8
MountingSurface MountLead Free Status / RoHS StatusCompliant
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
8
Page 8
9
Page 9
10
Page 10
11
12
13
14
15
16
17
18
19
Page 7/19

Download datasheet (534Kb)Embed
PrevNext
3
Functional Description
3.1
General
The ICE2PCS01/G is a 8 pin control IC for power factor
correction converters. It comes in both DIP and DSO
packages and is suitable for wide range line input
applications from 85 to 265 VAC. The IC supports
converters in boost topology and it operates in
continuous conduction mode (CCM) with average
current control.
The IC operates with a cascaded control; the inner
current loop and the outer voltage loop. The inner
current loop of the IC controls the sinusoidal profile for
the average input current. It uses the dependency of
the PWM duty cycle on the line input voltage to
determine the corresponding input current. This means
the average input current follows the input voltage as
long as the device operates in CCM. Under light load
condition, depending on the choke inductance, the
system may enter into discontinuous conduction mode
(DCM). In DCM, the average current waveform will be
distorted but the resultant harmonics are still low
enough to meet the Class D requirement of IEC 1000-
3-2.
The outer voltage loop controls the output bus voltage.
Depending on the load condition, OTA1 establishes an
appropriate voltage at VCOMP pin which controls the
amplitude of the average input current.
The IC is equipped with various protection features to
ensure safe operating condition for both the system
and device. Important protection features are namely
Open-Loop protection, Current Limitation and Output
Over-voltage Protection.
3.2
Power Supply
An internal under voltage lockout (UVLO) block
monitors the VCC power supply. As soon as it exceeds
11.8V and the voltage at pin 6 (VSENSE) is >0.6V, the
IC begins operating its gate drive and performs its
Startup as shown in Figure 3.
.
(V
> 0.6 V)
(V
< 0.6 V)
VSENSE
VSENSE
V
CC
11.8 V
IC's
Start
Normal
Open loop/
OFF
Up
State
Operation
Standby
Figure 3
State of Operation respect to VCC
Version 2.2
If VCC drops below 11V, the IC is off. The IC will then
be consuming typically 300µA, whereas consuming
13mA during normal operation.
The IC can be turned off and forced into standby mode
by pulling down the voltage at pin 6 (VSENSE) to lower
than 0.6V. The current consumption is reduced to
300µA in this mode.
3.3
Figure 4 shows the operation of voltage loop’s OTA1
during startup. The VCOMP pin is pull internally to
ground via switch S1 during UVLO and other fault
conditions (see later section on “System Protection”).
During power up when V
rated level, OTA1 sources an output current, maximum
30µA, into the compensation network at pin 5
(VCOMP) causing the voltage at this pin to rise linearly.
This results in a controlled linear increase of the input
current from 0A thus reducing the stress on the
external component.
(
R 3 + R 4
R 6
C 4
Figure 4
As V
OUT
value, VCOMP voltage is level-shifted by the window
detect block as shown in Figure 5, to ensure there is
fast boost up of the output voltage.
(V
> 0.6 V)
VSENSE
When V
OUT
sourcing current drops and the level shift of the window
detect block is removed. The normal voltage loop then
takes control.
11.0 V
t
Normal
OFF
Operation
7
CCM-PFC
ICE2PCS01/G
Functional Description
Start-up
is less than 83% of the
OUT
V S E N S E
R 4
x V
)
O U T
OTA1
V C O M P
p ro te c t
S 1
IC E 2 P C S 0 1 /G
C 5
Startup Circuit
has not reached within 5% from the rated
approaches its rated value, OTA1’s
09 October 2007
3V