ADF4360-8BCPZ Analog Devices Inc, ADF4360-8BCPZ Datasheet - Page 17

• Manufacturer Part Number: ADF4360-8BCPZ
• Description: IC SYNTHESIZER VCO 24-LFCSP
• Manufacturer: Analog Devices Inc
• Type: Fanout Distribution, Integer N Synthesizer (RF)r

Specifications of ADF4360-8BCPZ

• Pll: Yes
• Input: CMOS
• Output: Clock
• Number Of Circuits: 1
• Ratio - Input:output: 1:2
• Differential - Input:output: No/No
• Frequency - Max: 400MHz
• Divider/multiplier: Yes/No
• Voltage - Supply: 3 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 24-LFCSP
• Frequency-max: 400MHz
• Pll Type: Frequency Synthesis
• Frequency: 400MHz
• Supply Current: 5mA
• Supply Voltage Range: 3V To 3.6V
• Digital Ic Case Style: LFCSP
• No. Of Pins: 24
• Operating Temperature Range: -40°C To +85°C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-ADF4360-8EBZ1 - BOARD EVALUATION FOR ADF4360-8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

POWER-UP
Power-Up Sequence
The correct programming sequence for the ADF4360-8 after
power-up is
1.
2.
3.
Initial Power-Up
Initial power-up refers to programming the part after the
application of voltage to the AV
initial power-up, an interval is required between programming
the control latch and programming the N counter latch. This
interval is necessary to allow the transient behavior of the
ADF4360-8 during initial power-up to settle.
During initial power-up, a write to the control latch powers up
the part, and the bias currents of the VCO begin to settle. If
Table 10. C
C
10 µF
440 nF
N
Value
R counter latch
Control latch
N counter latch
N
Recommended Interval
Between Control Latch
and N Counter Latch
≥15 ms
≥ 600 µs
Capacitance vs. Interval and Phase Noise
POWER-UP
CLOCK
DATA
LE
DD
, DV
DD
LATCH DATA
R COUNTER
, V
Open-Loop Phase Noise
@ 10 kHz Offset
(L1 and L2 = 18.0 nH)
−100 dBc/Hz
−99 dBc/Hz
VCO,
and CE pins. On
Figure 21. ADF4360-8 Power-Up Timing
LATCH DATA
Rev. A | Page 17 of 24
CONTROL
Open-Loop Phase Noise
@ 10 kHz Offset
(L1 and L2 = 110.0 nH)
−97 dBc/Hz
−96 dBc/Hz
these currents have not settled to within 10% of their steady-
state value, and if the N counter latch is then programmed, the
VCO may not oscillate at the desired frequency, which does not
allow the band select logic to choose the correct frequency
band, and the ADF4360-8 may not achieve lock. If the recom-
mended interval is inserted, and the N counter latch is pro-
grammed, the band select logic can choose the correct fre-
quency band, and the part locks to the correct frequency.
The duration of this interval is affected by the value of the
capacitor on the C
reduce the close-in noise of the ADF4360-8 VCO. The
recommended value of this capacitor is 10 µF. Using this value
requires an interval of ≥15 ms between the latching in of the
control latch bits and latching in of the N counter latch bits. If a
shorter delay is required, the capacitor can be reduced. A slight
phase noise penalty is incurred by this change, which is further
explained in Table 10.
CONTROL LATCH WRITE TO
N COUNTER LATCH WRITE
REQUIRED INTERVAL
N
pin (Pin 14). This capacitor is used to
LATCH DATA
N COUNTER
Open-Loop Phase Noise
@ 10 kHz Offset
(L1 and L2 = 560.0 nH)
−99 dBc/Hz
−98 dBc/Hz
ADF4360-8