ADF4360-8BCPZ Analog Devices Inc, ADF4360-8BCPZ Datasheet - Page 22

• Manufacturer Part Number: ADF4360-8BCPZ
• Description: IC SYNTHESIZER VCO 24-LFCSP
• Manufacturer: Analog Devices Inc
• Type: Fanout Distribution, Integer N Synthesizer (RF)r

Specifications of ADF4360-8BCPZ

• Pll: Yes
• Input: CMOS
• Output: Clock
• Number Of Circuits: 1
• Ratio - Input:output: 1:2
• Differential - Input:output: No/No
• Frequency - Max: 400MHz
• Divider/multiplier: Yes/No
• Voltage - Supply: 3 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 24-LFCSP
• Frequency-max: 400MHz
• Pll Type: Frequency Synthesis
• Frequency: 400MHz
• Supply Current: 5mA
• Supply Voltage Range: 3V To 3.6V
• Digital Ic Case Style: LFCSP
• No. Of Pins: 24
• Operating Temperature Range: -40°C To +85°C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-ADF4360-8EBZ1 - BOARD EVALUATION FOR ADF4360-8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

ADF4360-8
INTERFACING
The ADF4360 family has a simple SPI®-compatible serial inter-
face for writing to the device. CLK, DATA, and LE control the
data transfer. When LE goes high, the 24 bits that have been
clocked into the appropriate register on each rising edge of CLK
are transferred to the appropriate latch. See Figure 2 for the
timing diagram and Table 5 for the latch truth table.
The maximum allowable serial clock rate is 20 MHz. This
means that the maximum update rate possible is 833 kHz, or
one update every 1.2 µs. This is more than adequate for systems
that have typical lock times in hundreds of microseconds.
ADuC812 Interface
Figure 25 shows the interface between the ADF4360 family and
the ADuC812 MicroConverter®. Since the ADuC812 is based on
an 8051 core, this interface can be used with any 8051-based
microcontrollers. The MicroConverter is set up for SPI master
mode with CPHA = 0. To initiate the operation, the I/O port
driving LE is brought low. Each latch of the ADF4360 family
needs a 24-bit word, which is accomplished by writing three
8-bit bytes from the MicroConverter to the device. After the
third byte has been written, the LE input should be brought
high to complete the transfer.
I/O port lines on the ADuC812 are also used to control power-
down (CE input) and detect lock (MUXOUT configured as lock
detect and polled by the port input). When operating in the
described mode, the maximum SCLOCK rate of the ADuC812
is 4 MHz. This means that the maximum rate at which the
output frequency can be changed is 166 kHz.
ADuC812
I/O PORTS
SCLOCK
Figure 25. ADuC812 to ADF4360-x Interface
MOSI
SDATA
SCLK
CE
MUXOUT
(LOCK DETECT)
LE
ADF4360-x
Rev. A | Page 22 of 24
ADSP-2181 Interface
Figure 26 shows the interface between the ADF4360 family and
the ADSP-21xx digital signal processor. The ADF4360 family
needs a 24-bit serial word for each latch write. The easiest way
to accomplish this using the ADSP-21xx family is to use the
autobuffered transmit mode of operation with alternate fram-
ing. This provides a means for transmitting an entire block of
serial data before an interrupt is generated.
Set up the word length for 8 bits and use three memory loca-
tions for each 24-bit word. To program each 24-bit latch, store
the 8-bit bytes, enable the autobuffered mode, and write to the
transmit register of the DSP. This last operation initiates the
autobuffer transfer.
PCB DESIGN GUIDELINES FOR CHIP SCALE PACKAGE
The leads on the chip scale package (CP-24) are rectangular.
The printed circuit board pad for these should be 0.1 mm
longer than the package lead length and 0.05 mm wider than
the package lead width. The lead should be centered on the pad
to ensure that the solder joint size is maximized.
The bottom of the chip scale package has a central thermal pad.
The thermal pad on the printed circuit board should be at least
as large as this exposed pad. On the printed circuit board, there
should be a clearance of at least 0.25 mm between the thermal
pad and the inner edges of the pad pattern to ensure that short-
ing is avoided.
Thermal vias may be used on the printed circuit board thermal
pad to improve thermal performance of the package. If vias
are used, they should be incorporated into the thermal pad at
1.2 mm pitch grid. The via diameter should be between 0.3 mm
and 0.33 mm, and the via barrel should be plated with 1 ounce
of copper to plug the via.
The user should connect the printed circuit thermal pad to
AGND. This is internally connected to AGND.
ADSP-21xx
I/O PORTS
Figure 26. ADSP-21xx to ADF4360-x Interface
SCLOCK
MOSI
TFS
SDATA
SCLK
LE
CE
MUXOUT
(LOCK DETECT)
ADF4360-x