1-5145169-2 TE Connectivity, 1-5145169-2 Datasheet

CONNECTOR ASSEMBLY, DUAL POSITIONS, .050

1-5145169-2

Manufacturer Part Number
1-5145169-2
Description
CONNECTOR ASSEMBLY, DUAL POSITIONS, .050
Manufacturer
TE Connectivity
Datasheets

Specifications of 1-5145169-2

Pcb Mounting Orientation
Vertical
Number Of Dual Positions
92
Pcb Mount Style
Through Hole
Holddown Material
Brass
Holddown Plating
Tin over Nickel
Voltage (vac)
5
Termination Post Length (mm [in])
3.56 [0.140]
Solder Tail Contact Plating
Tin over Nickel
Number Of Positions
184
Centerline (mm [in])
1.27 [0.050]
Bus Width
64 Bit
Pcb Mount Retention Type
Hold Down Post(s)
Ejector
Without
Number Of Holddowns
3
Family Name
PCI
Contact Plating, Mating Area, Material
Gold (30)
Contact Base Material
Phosphor Bronze
Housing Color
White
Housing Material
Thermoplastic - GF
Rohs/elv Compliance
RoHS compliant, ELV compliant
Lead Free Solder Processes
Wave solder capable to 240°C, Wave solder capable to 260°C, Wave solder capable to 265°C
Rohs/elv Compliance History
Always was RoHS compliant
1.
1.1.
1.2.
2.
2.1.
3.
3.1.
3.2.
3.3.
©2011 Tyco Electronics Corporation,
a TE Connectivity Ltd. Company
All Rights Reserved
TE logo is a trademark.
SCOPE
Content
This specification covers perform ance, tests and quality requirem ents for the TE Connectivity (TE) .050
centerline card edge connector. This connector is a m ulti-contact edge board type having contacts for
solder applications.
Qualification
W hen tests are perform ed on subject product line, procedures specified in Figure 1 shall be used. All
inspections shall be perform ed using applicable inspection plan and product drawing.
APPLICABLE DOCUM ENTS
The following docum ents form a part of this specification to the extent specified herein. Unless
otherwise specified, latest edition of the docum ent applies. In the event of conflict between
requirem ents of this specification and product drawing, product drawing shall take precedence. In the
event of conflict between requirem ents of this specification and referenced docum ents, this specification
shall take precedence.
TE Docum ents
!
!
!
!
!
REQUIREM ENTS
Design and Construction
Product shall be of design, construction and physical dim ensions specified on applicable product
drawing.
Materials
!
!
Ratings
!
!
!
!
109-1: General Requirem ents for Test Specifications
109 Series: Test Specifications as indicated in Figure 1
114-13148: Application Specification (.050 Series Standard Edge Peripheral Com puter
Interconnect (PCI) Surface Mount Connector Assem blies)
114-26012: Application Specification (Card Edge Connectors with Contacts on .050 Inch Centers)
501-203: Qualification Test Report (Connector, Card Edge, .050 Series)
Contact: Phosphor bronze, gold or gold flash/palladium nickel over nickel plating
Housing: PPS or PCT
Voltage: 203 volts AC
Current: Signal application only
Tem perature: -55 to 85°C
Flam m ability: UL94V-0
| Indicates change
*Trademark
Product
Specification
Connector, Card Edge, .050 Centerline
For latest revision, visit our website at www.te.com/documents.
For Regional Customer Service, visit our website at www.te.com
Other products, logos, and company names might be trademarks of their respective owners.
108-14034
11Mar11 Rev D
1 of 6
LOC B

Related parts for 1-5145169-2

1-5145169-2 Summary of contents

Page 1

... This connector ulti-contact edge board type having contacts for solder applications. 1.2. Qualification W hen tests are perform ed on subject product line, procedures specified in Figure 1 shall be used. All inspections shall be perform ed using applicable inspection plan and product drawing. 2. APPLICABLE DOCUM ENTS The following docum ents form a part of this specification to the extent specified herein ...

Page 2

... Perform ance and Test Description Product is designed to m eet electrical, m echanical and environm ental perform ance requirem ents specified in Figure 1. Unless otherwise specified, all tests shall be perform bient environm ental conditions per Test Specification 109-1. 3.5. Test Requirem ents and Procedures Sum m ary Test Description Exam ination of product ...

Page 3

... TE Spec 109-23-3, Condition B. Subject unm ated sam ples to 10 cycles between 25 and 65°C at 95% RH. TE Spec 109-43. Subject m ated sam ples to tem perature life at 85°C for 1000 hours. TE Spec 109-85-2. Subject m ated sam ples to environm ental class II for 14 days ...

Page 4

... Dielectric withstanding voltage Vibration Physical shock Durability Mating force Unm ating force Therm al shock Hum idity/tem perature cycling Tem perature life Mixed flowing gas (a) See paragraph 4.1.A. NOTE (b) Numbers indicate sequence in which tests are performed. (c) Precondition samples with 3 cycles durability. Rev D Test Group ( ...

Page 5

... Acceptance Acceptance is based on verification that product m eets requirem ents of Figure 1. Failures attributed to equipm ent, test setup or operator deficiencies shall not disqualify product. W hen product failure occurs, corrective action shall be taken and sam ples resubm itted for qualification. Testing to confirm corrective action is required before resubm ittal ...

Page 6

... Term ination Resistance Measurem ent Points Rev D Figure 3 Test Board Figure 4 108-14034 ...

Related keywords