M4T32-BR12SH6 STMicroelectronics, M4T32-BR12SH6 Datasheet - Page 13

• Manufacturer Part Number: M4T32-BR12SH6
• Description: IC SNAPHAT BATT/CRYSTAL 28-SOIC
• Manufacturer: STMicroelectronics

Specifications of M4T32-BR12SH6

• Battery Type: Li-(CF)
• Operating Supply Voltage: 0 V to 2.8 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Package / Case: SOIC-28
• Mounting Style: SMD/SMT
• Capacity: 120 mAh
• Chemical System: Lithium Poly-Carbonmonoflouride
• Primary Type: Pack
• Size: Cylindrical
• Standards: UL Recognized
• Temperature, Operating: -40 to +85 °C
• Temperature, Operating, Maximum: 85 °C
• Temperature, Operating, Minimum: -40 °C
• Termination: Snap-On
• Voltage, Battery: 3 V
• Voltage, Rating: 3 V
• Supply Voltage Range: 2.8V
• Battery Ic Case Style: SOIC
• No. Of Pins: 4
• Operating Temperature Range: -40°C To +85°C
• Crystal Terminals: Snap On
• Load Capacitance: 12.5pF
• Rohs Compliant: Yes
• Crystal Mounting Type: SMD
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-3688-5

M48T35AV
3
3.1
3.2
3.3
Clock operations
Reading the clock
Updates to the TIMEKEEPER
read to prevent reading data in transition. The BiPORT™ TIMEKEEPER cells in the RAM
array are only data registers and not the actual clock counters, so updating the registers can
be halted without disturbing the clock itself.
Updating is halted when a '1' is written to the READ bit, D6 in the control register 7FF8h. As
long as a '1' remains in that position, updating is halted.
After a halt is issued, the registers reflect the count; that is, the day, date, and the time that
were current at the moment the halt command was issued.
All of the TIMEKEEPER registers are updated simultaneously. A halt will not interrupt an
update in progress. Updating is within a second after the bit is reset to a '0.'
Setting the clock
Bit D7 of the control register 7FF8h is the WRITE bit. Setting the WRITE bit to a '1,' like the
READ bit, halts updates to the TIMEKEEPER
the correct day, date, and time data in 24-hour BCD format
WRITE bit to a '0' then transfers the values of all time registers 7FF9h-7FFFh to the actual
TIMEKEEPER counters and allows normal operation to resume. The FT bit and the bits
marked as '0' in
operation. After the WRITE bit is reset, the next clock update will occur within one second.
See the application note AN923, “TIMEKEEPER
information on century rollover.
Stopping and starting the oscillator
The oscillator may be stopped at any time. If the device is going to spend a significant
amount of time on the shelf, the oscillator can be turned off to minimize current drain on the
battery. The STOP bit is the MSB of the seconds register. Setting it to a '1' stops the
oscillator. The M48T35AV is shipped from STMicroelectronics with the STOP bit set to a '1.'
When reset to a '0,' the M48T35AV oscillator starts within 1 second.
Table 5
must be written to '0' to allow for normal TIMEKEEPER and RAM
®
Doc ID 6845 Rev 8
registers (see
®
Table
registers. The user can then load them with
®
rolling into the 21
5) should be halted before clock data is
(seeTable
st
5). Resetting the
century” for
Clock operations
13/29