S-35390A-T8T1G Seiko Instruments, S-35390A-T8T1G Datasheet - Page 38

• Manufacturer Part Number: S-35390A-T8T1G
• Description: IC RTC I2C 2-WIRE 8-TSSOP
• Manufacturer: Seiko Instruments
• Type: Clock/Calendarr

Specifications of S-35390A-T8T1G

• Time Format: HH:MM:SS (12/24 hr)
• Date Format: YY-MM-DD-dd
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 1.3 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-TSSOP
• Function: Clock/Calendar/Alarm/Battery Backup/Interrupt
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 1.3 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Rtc Bus Interface: Serial (2-Wire, I2C)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 728-1007-2

38
2-WIRE REAL-TIME CLOCK
S-35390A
Caution
Adjustment of Oscillation Frequency
1. Configuration of oscillator
Crystal oscillator: 32.768 kHz
Since crystal oscillation is sensitive to external noise (the clock accuracy is affected), the following measures are
essential for optimizing the oscillation configuration.
(1)
(2)
(3)
(4)
(5)
*1. When setting the value for the crystal oscillator’s C
*2. Design the board so that the parasitic capacitance is 5 pF.
*3. The oscillator operates unless C
advances.
Place the S-35390A, crystal oscillator, and external capacitor (C
Increase the insulation resistance between pins and the substrate wiring patterns of XIN and XOUT.
Do not place any signal or power lines close to the oscillator.
Locating the GND layer immediately below the oscillator is recommended.
Locate the bypass capacitor adjacent to the power supply pin of the S-35390A.
C
C
1. When using the crystal oscillator with a C
2. Oscillation characteristics is subject to the variation of each component such as substrate parasitic
L
g
= 6 pF
= None
oscillation operation may become unstable. Use a crystal oscillator with a C
capacitance, parasitic resistance, crystal oscillator, and C
sufficient attention for them.
*1
Parasitic capacitance
*2
to 9.1 pF
Parasitic capacitance
C
oscillator
g
Crystal
g
*3
Figure 49 Connection Diagram 1
Figure 50 Connection Diagram 2
is not connected. Note that the oscillation frequency is in the direction that it
Seiko Instruments Inc.
*3
C
g
L
as 7 pF, connect C
XIN
XOUT
1
2
3
4
L
Locate the GND layer in the
layer immediately below
C
exceeding the rated value (7 pF) (e.g : C
d
XIN
VSS
XOUT
S-35390A
g
) as close to each other as possible.
R
R
d
f
d
externally if necessary.
g
. When configuring an oscillator, pay
8
7
6
5
Oscillator internal constant
standard values:
S-35390A
L
value of 6 pF or 7 pF.
R
R
C
f
d
d
= 100 MΩ
= 100 kΩ
= 8 pF
Rev.3.0
L
= 12.5 pF),
_00