3 POS. CAP HSG., KEY A

184192-1

Manufacturer Part Number184192-1
Description3 POS. CAP HSG., KEY A
ManufacturerTE Connectivity
184192-1 datasheets
 


Specifications of 184192-1

Product LineSealed Sensor Connector (SSC)Product TypeConnector
Connector TypeHousingWire/cable TypeDiscrete Wire
Termination Method To Wire/cableCrimpStrain ReliefWithout
SealedNoMating Retention TypeLatching
KeyingAPanel Mount RetentionWithout
Panel Mount Retention TypeRetainer Clip SlotContact - Rated Current (a)10 – 17
Operating Voltage ReferenceAC/DCOperating Voltage (vac)125
Operating Voltage (vdc)125Wire/cable Size (awg)14 – 20, 18 – 22
Wire/cable Size (mm²)0.3 – 1, 0.5 – 2Profile Height (y-axis) (mm [in])20.20 [0.7952]
Wire TypeStrandedNumber Of Positions3
Number Of Rows1Mating RetentionWith
Length (x-axis) (mm [in])42.30 [1.6653]Width (z-axis) (mm [in])24.00 [0.945]
Contact TypeTabCircuit Number(s) BlockedNone
Connector StyleReceptacleHousing MaterialPBT - GF15
Housing ColorBlackMating AlignmentWith
Mating Alignment TypeKeyedRohs/elv ComplianceELV compliant
Lead Free Solder ProcessesNot reviewed for lead free solder processRohs/elv Compliance HistoryAlways was ELV compliant
Ip Dust Sealing Level6Ip Water Sealing Level7, 4
Agency/standardSAE/USCAR-2, IEC 529 IP 65/67Operating Temperature (°c [°f])-40 – +125 [-40 – +257]
Applies ToWire/CableAccepts Wire Insulation Diameter, Range (mm [in])1.20 – 2.10 [0.047 – 0.082], 1.20 – 2.70 [0.047 – 0.106]
Application UseWire-to-Wire / Wire-to-PanelContact Transmits (typical Application)Power
Packaging MethodBoxPackaging Quantity1500
For Use WithLock Plate  
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
8
Page 8
9
Page 9
Page 1/9

Download datasheet (454Kb)Embed
Next
Product
Specification
Sealed Sensor Connector System
1.
SCOPE
1.1.
Content
This specification covers performance, tests and quality requirements for the TE Connectivity (TE)
Sealed Sensor Connector (SSC) system.
1.2.
Qualification
When tests are performed on the subject product line, procedures specified in Figure 1 shall be used.
All inspections shall be performed using the applicable inspection plan and product drawing.
1.3.
Qualification Test Results
Successful qualification testing on the subject product line was completed in December of 2003. The
Qualification Test Report number for this testing is 501-575. This documentation is on file at and
available from Engineering Practices and Standards (EPS).
2.
APPLICABLE DOCUMENTS
The following documents form a part of this specification to the extent specified herein. Unless
otherwise specified, the latest edition of the document applies. In the event of conflict between the
requirements of this specification and the product drawing, the product drawing shall take precedence.
In the event of conflict between the requirements of this specification and the referenced documents,
this specification shall take precedence.
2.1.
TE Document
501-575: Qualification Test Report
2.2.
Commercial Standards
!
SAE/USCAR-2 (Rev 8/97): Standard for Automotive Electrical Connection Systems
!
SAE/USCAR-2 (Rev 3, 4/01): Performance Standard For Automotive Electrical Connector
Systems
3.
REQUIREMENTS
3.1.
Design and Construction
Product shall be of the design, construction and physical dimensions specified on the applicable product
drawing.
3.2.
Materials
Materials used in the construction of this product shall be as specified on the applicable product
drawing.
©2011 Tyco Electronics Corporation,
| Indicates change
a TE Connectivity Ltd. Company
*Trademark
All Rights Reserved
TE logo is a trademark.
For latest revision, visit our website at www.te.com/documents.
For Regional Customer Service, visit our website at www.te.com
Other products, logos, and company names might be trademarks of their respective owners.
108-1790
11Mar11 Rev B
1 of 9
LOC B

184192-1 Summary of contents

  • Page 1

    ... Sealed Sensor Connector System 1. SCOPE 1.1. Content This specification covers performance, tests and quality requirements for the TE Connectivity (TE) Sealed Sensor Connector (SSC) system. 1.2. Qualification When tests are performed on the subject product line, procedures specified in Figure 1 shall be used. All inspections shall be performed using the applicable inspection plan and product drawing. ...

  • Page 2

    Ratings ! Voltage: 125 volts AC/DC ! Current: See Figure 4 for applicable current carrying capability ! Operating Temperature: • Nylon housings: -40 to 150° C • PBT housings: -40 to 125° C 3.4. Performance and Test Description Product ...

  • Page 3

    Test Description Disengaging force (terminal-terminal). Engaging force (terminal-connector). Engaging force (terminal-connector). Engaging force (connector-connector). Disengaging force (connector-connector). Locking plate (TPA) engaging force. Locking plate (TPA) disengaging force. Terminal bend resistance. Thermal shock. Rev B Requirement 2.5 Newtons minimum. 15 Newtons ...

  • Page 4

    Test Description High temperature exposure. Humidity-temperature cycling. Immersion. Pressure/vacuum leak. Shall meet visual requirements, show no physical damage, and meet requirements of additional NOTE tests as specified in the Product Qualification and Requalification Test Sequence shown in Figure 2. Rev ...

  • Page 5

    Product Qualification and Requalification Test Sequence Test or Examination Dry circuit resistance Voltage drop Isolation resistance Durability (10 cycles) Vibration (Profile) Mechanical shock Engaging force (terminal-terminal) Disengaging force (terminal-terminal) Insertion force (terminal-connector) Extraction force (terminal-connector) Mating force (connector-connector) Unmating ...

  • Page 6

    QUALITY ASSURANCE PROVISIONS 4.1. Qualification Testing A. Specimen Selection Specimens shall be prepared in accordance with applicable Instruction Sheets and shall be selected at random from current production. Test groups 1, 2 and 3 shall each consist of 30 ...

  • Page 7

    Number of Positions Vibration & Mechanical Shock Mounting Fixture Rev B Wire Size Rated Current (AWG) (amperes Reduction Coefficient ...

  • Page 8

    Rev B Figure 6 Vibration Profile Figure 7 Contact Bend Fixture 108-1790 ...

  • Page 9

    Rev B Figure 8 Humidity-Temperature Cycling Profile 108-1790 ...