184192-1 TE Connectivity, 184192-1 Datasheet - Page 6

• Manufacturer Part Number: 184192-1
• Description: 3 POS. CAP HSG., KEY A
• Manufacturer: TE Connectivity

Specifications of 184192-1

• Product Line: Sealed Sensor Connector (SSC)
• Product Type: Connector
• Connector Type: Housing
• Wire/cable Type: Discrete Wire
• Termination Method To Wire/cable: Crimp
• Strain Relief: Without
• Sealed: No
• Mating Retention Type: Latching
• Keying: A
• Panel Mount Retention: Without
• Panel Mount Retention Type: Retainer Clip Slot
• Contact - Rated Current (a): 10 – 17
• Operating Voltage Reference: AC/DC
• Operating Voltage (vac): 125
• Operating Voltage (vdc): 125
• Wire/cable Size (awg): 14 – 20, 18 – 22
• Wire/cable Size (mm²): 0.3 – 1, 0.5 – 2
• Profile Height (y-axis) (mm [in]): 20.20 [0.7952]
• Wire Type: Stranded
• Number Of Positions: 3
• Number Of Rows: 1
• Mating Retention: With
• Length (x-axis) (mm [in]): 42.30 [1.6653]
• Width (z-axis) (mm [in]): 24.00 [0.945]
• Contact Type: Tab
• Circuit Number(s) Blocked: None
• Connector Style: Receptacle
• Housing Material: PBT - GF15
• Housing Color: Black
• Mating Alignment: With
• Mating Alignment Type: Keyed
• Rohs/elv Compliance: ELV compliant
• Lead Free Solder Processes: Not reviewed for lead free solder process
• Rohs/elv Compliance History: Always was ELV compliant
• Ip Dust Sealing Level: 6
• Ip Water Sealing Level: 7, 4
• Agency/standard: SAE/USCAR-2, IEC 529 IP 65/67
• Operating Temperature (°c [°f]): -40 – +125 [-40 – +257]
• Applies To: Wire/Cable
• Accepts Wire Insulation Diameter, Range (mm [in]): 1.20 – 2.10 [0.047 – 0.082], 1.20 – 2.70 [0.047 – 0.106]
• Application Use: Wire-to-Wire / Wire-to-Panel
• Contact Transmits (typical Application): Power
• Packaging Method: Box
• Packaging Quantity: 1500
• For Use With: Lock Plate

4.
4.1.
4.2.
4.3.
4.4.
Rev B
QUALITY ASSURANCE PROVISIONS
Qualification Testing
A.
B.
Requalification Testing
If changes significantly affecting form, fit or function are made to the product or manufacturing process,
product assurance shall coordinate requalification testing, consisting of all or part of the original testing
sequence as determined by development/product, quality and reliability engineering.
Acceptance
Acceptance is based on verification that the product meets the requirements of Figure 1. Failures
attributed to equipment, test setup or operator deficiencies shall not disqualify the product. When
product failure occurs, corrective action shall be taken and specimens resubmitted for qualification.
Testing to confirm corrective action is required before resubmittal.
Quality Conformance Inspection
The applicable quality inspection plan shall specify the sampling acceptable quality level to be used.
Dimensional and functional requirements shall be in accordance with the applicable product drawing
and this specification.
TOTAL VOLTAGE DROP (BETWEEN V
Specimen Selection
Specimens shall be prepared in accordance with applicable Instruction Sheets and shall be
selected at random from current production. Test groups 1, 2 and 3 shall each consist of 30
contact pairs. Test groups 4 and 5 shall consist of 30 connector assemblies. Test groups 6 through
13 shall each consist of 15 connector assemblies using the smallest applicable wire size.
Test Sequence
Qualification inspection shall be verified by testing specimens as specified in Figure 2.
THEREFORE: V.D.
PRIOR TO TESTING V.D.
Termination Resistance & Voltage Drop Setup
INTERFACE BULK + CRIMP
TAB BULK
1
& V
Figure 3
AND V.D.
2
) = V.D.
= V.D.
TAB BULK
WIRE
TOTAL
WILL BE DETERMINED
+ V.D.
- V.D.
TAB BULK
INTERFACE BULK CRIMP
- V.D.
WIRE
+ V.D.
108-1790
WIRE
6 of 9