MCP3021A5T-E/OT Microchip Technology, MCP3021A5T-E/OT Datasheet
MCP3021A5T-E/OT
Specifications of MCP3021A5T-E/OT
MCP3021A5T-E/OTTR
Available stocks
Related parts for MCP3021A5T-E/OT
MCP3021A5T-E/OT Summary of contents
Page 1
... AIN 2003 Microchip Technology Inc. Description The Microchip Technology Inc. MCP3021 is a succes- sive approximation A/D converter (ADC) with 10-bit resolution. Available in the SOT-23 package, this device provides one single-ended input with very low power consumption. Based on an advanced CMOS technology, the MCP3021 provides a low maximum conversion current and standby current of 250 µ ...
Page 2
... Ground Analog Input Serial Data In/Out Serial Clock In = 5.0V GND Units Conditions bits LSB LSB No missing codes LSB LSB 0. kHz 0. kHz 0. kHz IN V 2.7V V 5.5V DD µ mA 1. 400 kHz only SCL 2003 Microchip Technology Inc. ...
Page 3
... TEMPERATURE SPECIFICATIONS Electrical Characteristics: All parameters apply across the operating voltage range. Parameters Temperature Ranges Extended Temperature Range Operating Temperature Range Storage Temperature Range Thermal Package Resistances Thermal Resistance, 5L-SOT23A 2003 Microchip Technology Inc. = 400 kHz (Note 3). SCL Sym Min Typ Max I -1 — ...
Page 4
... T V HIGH HYS T T HD:DAT SU:DAT GND -40°C to +85°C. A Conditions kHz From (Note From (Note Note 2 ns SDA and SCL pins (Note 1) kHz From (Note From (Note Note 2 ns SDA and SCL pins (Note SU:STO T BUF 2003 Microchip Technology Inc. ...
Page 5
... Digital Code FIGURE 2-3: INL vs. Code (Representative Part). 2003 Microchip Technology Inc 5V 0V Fast Mode Timing (SCL = 400 kHz), Continuous Conversion SS 0.25 1 0.20 0.8 0.15 0.6 0.10 0.4 0.005 0 ...
Page 6
... Mode (f = 400 kHz). SCL Positive INL Negative INL - 100 125 Temperature (°C) INL vs. Temperature Positive DNL Negative DNL 100 200 300 400 Bus Rate (kHz) DNL vs. Clock Rate Positive DNL Negative DNL 3 3.5 4 4.5 5 5 DNL vs Fast DD 2003 Microchip Technology Inc. ...
Page 7
... V (V) DD FIGURE 2-15: Gain Error vs. V 2003 Microchip Technology Inc 5V 0V Fast Mode Timing (SCL = 400 kHz), Continuous Conversion SS 0.5 0.4 0.3 0.2 0.1 0 -0.1 -0.2 -0.3 -0.4 -0.5 768 1024 ...
Page 8
... FIGURE 2-22: Temperature FIGURE 2-23 -40 FIGURE 2-24: Level 2. 100 125 Temperature (°C) Offset Error vs 2. Input Frequency (kHz) SINAD vs. Input Frequency 2.7V DD -30 -20 -10 0 Input Signal Level (dB) SINAD vs. Input Signal 2003 Microchip Technology Inc. ...
Page 9
... Frequency (Hz) FIGURE 2-27: Spectrum Using I Mode (Representative Part, 1 kHz Input Frequency). 2003 Microchip Technology Inc 5V 0V Fast Mode Timing (SCL = 400 kHz), Continuous Conversion 9.5 11.5 9.0 11 8.5 10.5 8.0 10 7.7 9.5 7 ...
Page 10
... FIGURE 2-34: Rate. 100 -50 100 125 FIGURE 2-35: Temperature 5.5 2.5 . FIGURE 2-36 2.7V DD 100 200 300 400 Clock Rate (kHz) I (Active Bus) vs. Clock DDA 2. 100 125 Temperature (°C) I (Active Bus) vs. DDA 3 3.5 4 4.5 5 5 (Standby) vs DDS DD 2003 Microchip Technology Inc. ...
Page 11
... Temperature (°C) FIGURE 2-38: Analog Input Leakage vs. Temperature. 2003 Microchip Technology Inc 5V 0V Fast Mode Timing (SCL = 400 kHz), Continuous Conversion SS 2.1 Test Circuit 75 100 125 2.5V CM FIGURE 2-39: 100 125 MCP3021 ...
Page 12
... For normal data transfer, SDA is allowed to change only during SCL low. Changes during SCL high are reserved for indicating the START and STOP conditions (refer to Section 6.1, “Driving the Analog Input”). to SS for 100 kHz and Bus”). 2003 Microchip Technology Inc. ...
Page 13
... FIGURE 4-1: Transfer Function. 2003 Microchip Technology Inc. 4.2 Conversion Time (t The conversion time is the time required to obtain the digital result once the analog input is disconnected from the holding capacitor. With the MCP3021, the specified conversion time is typically 8.96 µ ...
Page 14
... The average amount of current required while no con- version is occurring and while no data is being output (i.e., SCL and SDA lines are quiet Standard Mode Timing specification where the frequency of SCL is 100 kHz Fast Mode Timing specification where the frequency of SCL is 400 kHz. 2003 Microchip Technology Inc ...
Page 15
... START CONDITION FIGURE 5-1: Data Transfer Sequence on the Serial Bus. 2003 Microchip Technology Inc. Each data transfer is initiated with a START condition and terminated with a STOP condition. The number of data bytes transferred between the START and STOP conditions is determined by the master device and is unlimited ...
Page 16
... Start Bit FIGURE 5-3: Address Byte. R SCL 1 SDA D6 1 FIGURE 5-4: Continuous Conversions ACQ CONV initiated here Address Byte R/W Device bits Address bits Initiating the Conversion ACQ CONV initiated here Lower Data Byte ( Initiating the Conversion, 2003 Microchip Technology Inc. ...
Page 17
... Device bits Address bits FIGURE 5-6: Continuous Conversion. 2003 Microchip Technology Inc. 5.3.2 READING THE CONVERSION DATA After the MCP3021 acknowledges the address byte, the device will transmit four ‘0’ bits followed by the upper four data bits of the conversion. The master device will then acknowledge this byte with an ACK = low ...
Page 18
... Figure 6-3. PIC16F876 Microcontroller Analog MCP3021 10-bit ADC Input Signal 2 C FIGURE 6-3: ) adds to the inter impedance, directly affecting S SAMPLE Sampling Switch SAMPLE = DAC capacitance = SDA SCL 24LC01 EEPROM TC74 Temperature Sensor 2 Multiple Devices Bus. 2003 Microchip Technology Inc. ). ...
Page 19
... Digital and analog traces should be separated as much as possible on the board, with no traces running underneath the device or the bypass capacitor. Extra 2003 Microchip Technology Inc. precautions should be taken to keep traces with high frequency signals (such as clock lines) as far as possible from analog traces. ...
Page 20
... MCP3021 7.0 PACKAGING INFORMATION 7.1 Package Marking Information MCP3021A0T-E/OT MCP3021A1T-E/OT MCP3021A2T-E/OT MCP3021A3T-E/OT MCP3021A4T-E/OT MCP3021A5T-E/OT MCP3021A6T-E/OT MCP3021A7T-E/OT * Default option. Contact Microchip Factory for other address options. Legend: 1 Part Number code + temperature range 2 Part Number code + temperature range 3 Year and work week 4 Lot ID ...
Page 21
... Mold Draft Angle Top Mold Draft Angle Bottom * Controlling Parameter § Significant Characteristic Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010” (0.254mm) per side. JEDEC Equivalent: MO-178 Drawing No. C04-091 2003 Microchip Technology Inc Units ...
Page 22
... MCP3021 NOTES: DS21805A-page 22 2003 Microchip Technology Inc. ...
Page 23
... MCP3021A1T-E/OT: Extended, A1 Address, Tape and Reel MCP3021A2T-E/OT: Extended, A2 Address, Tape and Reel MCP3021A3T-E/OT: Extended, A3 Address, Tape and Reel MCP3021A4T-E/OT: Extended, A4 Address, Tape and Reel MCP3021A5T-E/OT: Extended, A5 Address, Tape and Reel MCP3021A6T-E/OT: Extended, A6 Address, Tape and Reel MCP3021A7T-IE/OT: Extended, A7 Address, Tape and Reel DS21805A-page 23 ...
Page 24
... MCP3021 NOTES: DS21805A-page 24 2003 Microchip Technology Inc. ...
Page 25
... Serialized Quick Turn Programming (SQTP service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. © 2003, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received QS-9000 quality system ...
Page 26
... Korea Microchip Technology Korea 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea 135-882 Tel: 82-2-554-7200 Fax: 82-2-558-5934 Singapore Microchip Technology Singapore Pte Ltd. 200 Middle Road #07-02 Prime Centre Singapore, 188980 Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan Microchip Technology (Barbados) Inc., Taiwan Branch 11F-3, No ...