MCP3001-I/SN Microchip Technology, MCP3001-I/SN Datasheet
MCP3001-I/SN
Specifications of MCP3001-I/SN
Available stocks
Related parts for MCP3001-I/SN
MCP3001-I/SN Summary of contents
Page 1
... LSB max. Communication with the device is done using a simple serial interface compatible with the SPI protocol. The device is capable of sample rates up to 200 ksps at a clock rate of 2.8 MHz. The MCP3001 operates over a broad voltage range Low current design permits operation with a typical standby current of only 5 nA and a typical active current of 400 µ ...
Page 2
... MCP3001 1.0 ELECTRICAL CHARACTERISTICS 1.1 Maximum Ratings* V .........................................................................7.0V DD All inputs and outputs w.r.t. V ...... -0. Storage temperature ..........................-65°C to +150°C Ambient temp. with power applied .....-65°C to +125°C ESD protection on all pins (HBM)........................> 4kV *Notice: Stresses above those listed under “Maximum ratings” ...
Page 3
... DIS t 350 — — CSH t — — 100 R t — — 100 F level. REF MCP3001 = 200 ksps and f = 14*f SAMPLE CLK SAMPLE Units Conditions °C °C °C °C/W °C/W °C/W °C µA Ω See Figure 4-1 pF See Figure 4-1 ...
Page 4
... MCP3001 All parameters apply 5V unless otherwise noted. Typical values apply for V Parameter Power Requirements: Operating Voltage Operating Current Standby Current Note 1: This parameter is guaranteed by characterization and not 100% tested. 2: See graph that relates linearity performance Because the sample cap will eventually lose charge, clock rates below 10 kHz can affect linearity perfor- mance, especially at elevated temperatures ...
Page 5
... Waveform 1 is for an output with internal condi- tions such that the output is high, unless disabled by the output control. † Waveform 2 is for an output with internal condi- tions such that the output is low, unless disabled by the output control. MCP3001 and t DIS Waveform 2 ...
Page 6
... MCP3001 2.0 TYPICAL PERFORMANCE CHARACTERISTICS Note: The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e ...
Page 7
... FIGURE 2-11: Differential Nonlinearity (DNL) vs. Sample Rate (V 1.0 0.8 0.6 0.4 0.2 0.0 -0.2 -0.4 -0.6 -0.8 -1 0.0 FIGURE 2-12: Differential Nonlinearity (DNL) vs 2.7V). DD MCP3001 = 25° 2.7V REF = 75 ksps Positive INL Negative INL - 100 Temperature (°C) Nonlinearity (INL) vs. = 2.7V 2.7V ...
Page 8
... MCP3001 Note: Unless otherwise indicated 0 REF 0 200 ksps SAMPLE 0.3 0.2 0.1 0.0 -0.1 -0.2 -0.3 -0.4 -0.5 0 128 256 384 512 640 Digital Code FIGURE 2-13: Differential Nonlinearity (DNL) vs. Code (Representative Part). 0.3 0.2 Positive DNL 0.1 0.0 -0.1 Negative DNL -0 ...
Page 9
... REF = 200 ksps 100 1 FIGURE 2-23: Signal to Noise Ratio and Distortion (SINAD) vs. Input Frequency REF f SAMPLE 50 = 200 ksps 100 -40 FIGURE 2-24: Signal (SINAD) vs. Input Signal Level. MCP3001 = 25° REF = 200 ksps 2.7V DD REF ksps SAMPLE - 100 Temperature (° 2.7V DD REF REF ...
Page 10
... MCP3001 Note: Unless otherwise indicated 10.0 9.9 9 REF SAMPLE 9 ksps SAMPLE 9.4 9.3 9.2 9.1 9.0 0.0 1.0 2.0 3.0 V (V) REF FIGURE 2-25: Effective Number of Bits (ENOB) vs REF 100 SAMPLE 2.7V DD REF ksps SAMPLE Input Frequency (kHz) FIGURE 2-26: Spurious ...
Page 11
... FIGURE 2-34: I 120 110 100 10000 10 FIGURE 2-35: I 120 110 100 100 -50 FIGURE 2-36: I MCP3001 = 25° 2.8 MHz except CLK = V = 2.5V 1.05 MHz DD CLK 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 V ( REF REF 2.7V DD REF ...
Page 12
... MCP3001 Note: Unless otherwise indicated REF 2.0 2.5 3.0 3.5 4.0 4.5 V (V) DD FIGURE 2-37 DDS DD 100. REF 10.00 1.00 0.10 0.01 -50 - Temperature (°C) FIGURE 2-38: I vs. Temperature. DDS DS21293C-page 5V 200 ksps 14*Sample Rate,T REF SAMPLE CLK 2.0 1 1.6 1.4 1 ...
Page 13
... Conversion rates of 200 ksps are possible on the MCP3001. See Section 6.2 for informa- tion on minimum clock rates. Communication with the device is done using a 3-wire SPI-compatible interface. ...
Page 14
... MCP3001 V CHx PIN 7 pF Legend VA = signal source R = source impedance SS CHx = input channel pad C = input pin capacitance PIN V = threshold voltage leakage current at the pin LEAKAGE due to various junctions SS = sampling switch R = sampling switch resistor sample/hold capacitance SAMPLE FIGURE 4-1: Analog Input Model. 4.0 ...
Page 15
... SERIAL COMMUNICATIONS Communication with the device is done using a stan- dard SPI compatible serial interface. Initiating commu- nication with the MCP3001 begins with the CS going low. If the device was powered up with the CS pin low, it must be brought high and back low to initiate commu- nication ...
Page 16
... HI-Z NULL BIT OUT ? ? Data stored into MCU receive register after transmission of first 8 bits FIGURE 6-1: SPI Communication with the MCP3001 using 8-bit segments (Mode 0,0: SCLK idles low). CS CLK HI-Z NULL BIT OUT ? ? Data stored into MCU receive register after transmission of first 8 bits FIGURE 6-2: SPI Communication with the MCP3001 using 8-bit segments (Mode 1,1: SCLK idles high) ...
Page 17
... Maintaining Minimum Clock Speed When the MCP3001 initiates the sample period, charge is stored on the sample capacitor. When the sample period is complete, the device converts one bit for each clock that is received important for the user to note that a slow clock rate will allow charge to bleed off the sample cap while the conversion is taking place. At 85° ...
Page 18
... Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. DS21293C-page 18 Example: MCP3001 e I/PNNN 3 0736 Example: MCP3001 e ISN 0736 3 NNN Example: e 3001I 3 725NNN Example: ...
Page 19
... Dimension Limits MIN N e .100 BSC A – A2 .115 A1 .015 E .290 E1 .240 D .348 L .115 c .008 b1 .040 b .014 eB – MCP3001 c NOM MAX 8 – .210 .130 .195 – – .310 .325 .250 .280 .365 .400 .130 .150 .010 .015 .060 .070 .018 .022 – .430 ...
Page 20
... MCP3001 8-Lead Plastic Small Outline (SN) – Narrow, 3.90 mm Body [SOIC] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging N NOTE Number of Pins Pitch Overall Height Molded Package Thickness § Standoff Overall Width Molded Package Width ...
Page 21
... BSC A – – A2 0.75 0.85 A1 0.00 – E 4.90 BSC E1 3.00 BSC D 3.00 BSC L 0.40 0.60 L1 0.95 REF φ 0° – c 0.08 – b 0.22 – Microchip Technology Drawing C04-111B MCP3001 φ L MAX 1.10 0.95 0.15 0.80 8° 0.23 0.40 DS21293C-page 21 ...
Page 22
... MCP3001 8-Lead Plastic Thin Shrink Small Outline (ST) – 4.4 mm Body [TSSOP] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging D N NOTE Number of Pins Pitch Overall Height Molded Package Thickness Standoff Overall Width Molded Package Width ...
Page 23
... APPENDIX A: REVISION HISTORY Revision C (January 2007) This revision includes updates to the packaging diagrams. © 2007 Microchip Technology Inc. MCP3001 DS21293C-page 23 ...
Page 24
... NOTES: DS21293C-page 24 © 2007 Microchip Technology Inc. ...
Page 25
... Plastic SOIC (150 mil Body), 8-lead MS = Plastic Micro Small Outline (MSOP), 8-lead ST = Plastic TSSOP (4.4 mm), 8-lead © 2007 Microchip Technology Inc. MCP3001 Examples: a) MCP3001-I/P: Industrial Temperature, PDIP package. b) MCP3001-I/SN: Industrial Temperature, SOIC package. c) MCP3001-I/ST: Industrial Temperature, TSSOP package. d) MCP3001-I/MS: Industrial Temperature, MSOP package. DS21293C-page25 ...
Page 26
... MCP3001 NOTES: DS21293C-page26 © 2007 Microchip Technology Inc. ...
Page 27
... Select Mode, Smart Serial, SmartTel, Total Endurance, UNI/O, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. ...
Page 28
... Fax: 886-3-572-6459 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 © 2007 Microchip Technology Inc. EUROPE Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 France - Paris Tel: 33-1-69-53-63-20 ...