AD6644ASTZ-65 Analog Devices Inc, AD6644ASTZ-65 Datasheet - Page 13

IC ADC 14BIT 65MSPS CMOS 52-LQFP

AD6644ASTZ-65

Manufacturer Part Number
AD6644ASTZ-65
Description
IC ADC 14BIT 65MSPS CMOS 52-LQFP
Manufacturer
Analog Devices Inc
Datasheet

Specifications of AD6644ASTZ-65

Data Interface
Parallel
Number Of Bits
14
Sampling Rate (per Second)
65M
Number Of Converters
4
Power Dissipation (max)
1.3W
Voltage Supply Source
Analog and Digital
Operating Temperature
-25°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
52-LQFP
Resolution (bits)
14bit
Sampling Rate
65MSPS
Input Channel Type
Differential
Supply Voltage Range - Digital
3V To 3.6V
Supply Current
245mA
Number Of Elements
1
Resolution
14Bit
Architecture
Pipelined
Sample Rate
65MSPS
Input Polarity
Unipolar
Input Type
Voltage
Rated Input Volt
±1.1V
Differential Input
Yes
Power Supply Requirement
Analog and Digital
Single Supply Voltage (typ)
5V
Single Supply Voltage (min)
4.85V
Single Supply Voltage (max)
5.25V
Dual Supply Voltage (typ)
Not RequiredV
Dual Supply Voltage (min)
Not RequiredV
Dual Supply Voltage (max)
Not RequiredV
Power Dissipation
1.5W
Differential Linearity Error
-1LSB/1.5LSB
Integral Nonlinearity Error
±0.5LSB(Typ)
Operating Temp Range
-25C to 85C
Operating Temperature Classification
Commercial
Mounting
Surface Mount
Pin Count
52
Package Type
LQFP
Input Signal Type
Differential
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AD6644ASTZ-65
Quantity:
3 047
Part Number:
AD6644ASTZ-65
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Part Number:
AD6644ASTZ-65
Manufacturer:
ADI/亚德诺
Quantity:
20 000
TERMINOLOGY
Analog Bandwidth
The analog input frequency at which the spectral power of the
fundamental frequency (as determined by the FFT analysis) is
reduced by 3 dB.
Aperture Delay
The delay between the 50% point of the rising edge of the
ENCODE command and the instant at which the analog input
is sampled.
Aperture Uncertainty (Jitter)
The sample-to-sample variation in aperture delay.
Differential Analog Input Resistance, Differential Analog
Input Capacitance, and Differential Analog Input Impedance
The real and complex impedances measured at each analog
input port. The resistance is measured statically and the
capacitance and differential input impedances are measured
with a network analyzer.
Differential Analog Input Voltage Range
The peak-to-peak differential voltage that must be applied to
the converter to generate a full-scale response. Peak differential
voltage is computed by observing the voltage on a single pin
and subtracting the voltage from the other pin, which is 180°
out of phase. Peak-to-peak differential is computed by rotating the
input phase 180° and taking the peak measurement again. The
difference is then computed between both peak measurements.
Differential Nonlinearity
The deviation of any code width from an ideal 1 LSB step.
Encode Pulse Width/Duty Cycle
Pulse width high is the minimum amount of time that the
ENCODE pulse should be left in the Logic 1 state to achieve
rated performance; pulse width low is the minimum time
ENCODE pulse should be left in a low state. Optimum
performance is achieved using a 50% duty cycle.
Full-Scale Input Power
Expressed in dBm. Computed using the following equation:
POWER
Full
Scale
=
10
log
V
2
Full
Z
. 0
001
Input
Scale
rms
Rev. D | Page 13 of 24
Harmonic Distortion, Second
The ratio of the rms signal amplitude to the rms value of the
second harmonic component, reported in dBc.
Harmonic Distortion, Third
The ratio of the rms signal amplitude to the rms value of the
third harmonic component, reported in dBc.
Integral Nonlinearity
The deviation of the transfer function from a reference line
measured in fractions of 1 LSB using a best straight line
determined by a least-square curve fit.
Minimum Conversion Rate
The encode rate at which the SNR of the lowest analog signal
frequency drops by no more than 3 dB below the guaranteed limit.
Maximum Conversion Rate
The encode rate at which parametric testing is performed.
Noise (for Any Range Within the ADC)
where:
Z is the input impedance.
FS is the full scale of the device for the frequency in question.
SNR is the value for the particular input level.
Signal is the signal level within the ADC reported in dB below
full scale.
V
Output Propagation Delay
The delay between a differential crossing of ENCODE and
ENCODE , and the time when all output data bits are within
valid logic levels.
Power Supply Rejection Ratio
The ratio of a change in input offset voltage to a change in
power supply voltage.
Signal-to-Noise and Distortion (SINAD)
The ratio of the rms signal amplitude (set 1 dB below full scale)
to the rms value of the sum of all other spectral components,
including harmonics, but excluding dc.
Signal-to-Noise Ratio (Without Harmonics)
The ratio of the rms signal amplitude (set at 1 dB below full
scale) to the rms value of the sum of all other spectral
components, excluding the first five harmonics and dc.
NOISE
V
includes both thermal and quantization noise.
NOISE
=
Z
×
. 0
001
×
10
FS
dBm
SNR
dBc
10
Signal
AD6644
dBFS

Related parts for AD6644ASTZ-65