1X1 MAG45(TM) 7G1,7G01,Y/G LED

 

5-6605809-9

Manufacturer Part Number5-6605809-9
Description1X1 MAG45(TM) 7G1,7G01,Y/G LED
ManufacturerTE Connectivity
5-6605809-9 datasheets

Availability: By request

International delivery:

Warranty: 60 days

Shipping & payment terms

Added to cart

Select quantity

 

Specifications of 5-6605809-9

Product TypeConnectorNumber Of Cores8
MagneticsIntegrated MagneticsJack TypeRJ45
Signal Routing TypeAuto MDI/MDIXProfileStandard
Pcb Mounting OrientationSide Entry (Right Angle)Jack Configuration1 x 1
Turns Ratio1:1ShieldedYes
Emi Finger - BottomWithoutTermination MethodSolder
Port ConfigurationSingleEmi Fingers -top And SidesWith
Latch OrientationInverted - Latch UpPcb Tail Length (mm [in])3.68 [0.145]
Contact Termination TypeThrough HolePreloadedYes
Connector StyleJackStatus IndicatorLED
Decoupling Capacitor2KVRear Pcb Ground TabWithout
Signal Lead Quantity10Rohs/elv ComplianceRoHS compliant, ELV compliant
Lead Free Solder ProcessesWave solder capable to 240°C, Wave solder capable to 260°C, Wave solder capable to 265°CRohs/elv Compliance HistoryAlways was RoHS compliant
Left Led Color (position #1)YellowRight Led Color (position #2)Green
Operating Temperature (°c [°f])0 – 70 [32 – 158]Applies ToPrinted Circuit Board
Environmental ConditionsOffice / PremisesApplicationGigabit Ethernet
show all specifications
1368398-1 PDF datasheet5-6605809-7 PDF datasheet #2
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
Page 1/6

Download datasheet (85Kb)Embed
Next
Product
Specification
Mag45* Modular Jacks With Integrated Magnetics
1.
SCOPE
1.1.
Content
This specification covers performance, tests and quality requirements for the TE Connectivity (TE)
Mag45* Modular Jacks with Integrated Magnetics.
1.2.
Qualification
When tests are performed on the subject product line, procedures specified in Figure 1 shall be used.
All inspections shall be performed using the applicable inspection plan and product drawing.
1.3.
Qualification Test Results
Successful qualification testing on the subject product line was completed on 20Jun00. The
Qualification Test Report number for this testing is 501-524. This documentation is on file at and
available from Engineering Practices and Standards (EPS).
2.
APPLICABLE DOCUMENTS
The following documents form a part of this specification to the extent specified herein. Unless
otherwise specified, the latest edition of the document applies. In the event of conflict between the
requirements of this specification and the product drawing, the product drawing shall take precedence.
In the event of conflict between the requirements of this specification and the referenced documents,
this specification shall take precedence.
2.1.
TE Documents
109-197:
TE Test Specifications vs EIA and IEC Test Methods
●
501-524:
Qualification Test Report
●
502-1129:
Engineering Report
●
2.2.
Industry Standards
ANSI X3.263:
Information Technology - Fibre Distributed Data Interface (FDDI) - Token Ring
●
Twisted Pair Physical Layer Medium Dependent (TP-PMD)
EIA-364:
Electrical Connector/Socket Test Procedures Including Environmental
●
Classifications
FCC Part 68:
Connection of Terminal Equipment to the Telephone, Connector Specifications
●
IEEE 802-3:
Local Area Networks: Carrier Sense Multiple Access With Collision Detection
●
(CSMA/CD) Access Method and Physical Layer Specification
MIL-STD-202: Test Method Standard - Electronic and Electrical Component Parts
●
MIL-STD-810: Test Method Standard - Environmental Engineering Considerations and
●
Laboratory Tests
3.
REQUIREMENTS
3.1.
Design and Construction
Product shall be of the design, construction and physical dimensions specified on the applicable
product drawing.
3.2.
Materials
Materials used in the construction of this product shall be as specified on the applicable product
drawing.
3.3.
Ratings
Voltage: 150 volts AC
●
Current: Signal application only
●
©2011 Tyco Electronics Corporation,
| Indicates Change
a TE Connectivity Ltd. Company
*Trademark
All Rights Reserved
TE logo is a trademark.
For latest revision, visit out website at www.te.com/documents
For Regional Customer service, visit our website at www.te.com
Other products, logos, and company names might be trademarks of their respective owners.
108-2100
30 Jan 12 Rev D
1 of 6
LOC B

Related parts for 5-6605809-9

Part Number DescriptionManufacturer Datasheet
5-6605850-8  5-6605850-8 TE Connectivity
5-6605809-5  5-6605809-5 1X1 MAG45(TM) 7G1,7G01,G/Y & G TE Connectivity
5-6605817-2  5-6605817-2 1X1 MAG45(TM)7UN2, 7U14C, G/Y TE Connectivity
5-6605809-7  5-6605809-7 1X1 MAG45(TM) 7G1,7G01,G/G LED TE Connectivity
5-6605844-1  5-6605844-1 1X1 MAG45(TM) 7H2ET,755,G/Y RL TE Connectivity
5-160433-6  5-160433-6 187 FASTON REC.IS TE Connectivity
5-103735-6  5-103735-6 Conn Shrouded Header HDR 7 POS 2.54mm Solder ST Thru-Hole Tube TE Connectivity
5-104069-6  5-104069-6 Conn Shrouded Header HDR 40 POS 1.27mm Solder RA Thru-Hole Tube TE Connectivity
5-5175473-6  5-5175473-6 .050CL,CHAMP,VERT PLUG,50 POSN TE Connectivity
5-102618-6  5-102618-6 Conn Shrouded Header HDR 16 POS 2.54mm Solder ST Thru-Hole TE Connectivity
5-5179009-6  5-5179009-6 0.8FH,R09H.5,140,08/SN,TU TE Connectivity
5-1478996-6  5-1478996-6 STRAIN RELIEF, BLACK, RG59 TE Connectivity
5-5179010-6  5-5179010-6 SOCKET, VERTICAL, 0.8MM, 13MM, 140WAY TE Connectivity
5-1394462-6  5-1394462-6 PLUG & SOCKET CONNECTOR, FEMALE, 1POS TE Connectivity
  5-1676480-6 TE Connectivity

5-6605809-9 Summary of contents

  • Page 1

    ... All inspections shall be performed using the applicable inspection plan and product drawing. 1.3. Qualification Test Results Successful qualification testing on the subject product line was completed on 20Jun00. The Qualification Test Report number for this testing is 501-524. This documentation is on file at and available from Engineering Practices and Standards (EPS). 2. APPLICABLE DOCUMENTS The following documents form a part of this specification to the extent specified herein ...

  • Page 2

    ... Extended temperature varieties: -40 to 85° C 3.4. Product Codes Product Codes for this product family are H363, H364, H365 and H366 3.5. Performance and Test Description Product is designed to meet the electrical, mechanical and environmental performance requirements specified in Figure 1. Unless otherwise specified, all tests shall be performed at ambient environmental conditions per EIA-364 ...

  • Page 3

    ... C with 60 minute dwell at temperature extremes. EIA-364-31B, Method IV. Subject mated and mounted specimens to 10 cycles (10 days) between 25 and 65° 95% RH. EIA-364-65, Class IIA (4 gas). Subject mated and unmated specimens to environmental Class IIA for 10 days. Subject mated and mounted ...

  • Page 4

    ... Numbers indicate sequence in which tests are performed. (c) Measure inductance initially and at 50, 100, 150, 200, 250, 300, 350, 400, 450, 500, 550, 600, 650, 700, 750, 800, 1000, 1200, 1400, 1600, 1800 and 2000 cycles. (d) 10 days mated; 5 days unmated; 5 days mated. ...

  • Page 5

    ... Specimen Selection Specimens shall be prepared in accordance with applicable Instruction Sheets and shall be selected at random from current production. Test group 1 shall consist of 16 specimens. Test groups 2 and 3 shall each consist of 1 specimen. Test group 4 shall consist of 45 specimens. B. Test Sequence Qualification inspection shall be verified by testing specimens as specified in Figure 2. ...

  • Page 6

    Rev D 108-2100 ...

Related keywords:

  • 5-6605809-9 datasheet
  • 5-6605809-9 data sheet
  • 5-6605809-9 pdf datasheet
  • 5-6605809-9 component
  • 5-6605809-9 part
  • 5-6605809-9 distributor
  • 5-6605809-9 RoHS
  • 5-6605809-9 datasheet download