MCP4342-103E/ST Microchip Technology, MCP4342-103E/ST Datasheet - Page 38

• Manufacturer Part Number: MCP4342-103E/ST
• Description: IC DGTL POT QUAD 10K 14TSSOP
• Manufacturer: Microchip Technology
• Series: WiperLock™r

Specifications of MCP4342-103E/ST

• Memory Type: Non-Volatile
• Taps: 129
• Resistance (ohms): 10K
• Number Of Circuits: 4
• Temperature Coefficient: 150 ppm/°C Typical
• Interface: SPI Serial
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 14-TSSOP
• Resistance In Ohms: 10K
• End To End Resistance: 10kohm
• Track Taper: Linear
• No. Of Steps: 129
• Supply Voltage Range: 2.7V To 5.5V
• Control Interface: Serial, SPI
• No. Of Pots: Quad
• Rohs Compliant: No
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

MCP434X/436X
REGISTER 4-3:
DS22233A-page 38
bit 8
Legend:
R = Readable bit
-n = Value at POR
bit 8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Note 1:
R-1
D8
These bits do not affect the wiper register values.
D8: Reserved. Forced to “1”
R3HW: Resistor 3 Hardware Configuration Control bit
This bit forces Resistor 3 into the “shutdown” configuration of the Hardware pin
1 = Resistor 3 is NOT forced to the hardware pin “shutdown” configuration
0 = Resistor 3 is forced to the hardware pin “shutdown” configuration
R3A: Resistor 3 Terminal A (P3A pin) Connect Control bit
This bit connects/disconnects the Resistor 3 Terminal A to the Resistor 3 Network
1 = P3A pin is connected to the Resistor 3 Network
0 = P3A pin is disconnected from the Resistor 3 Network
R3W: Resistor 3 Wiper (P3W pin) Connect Control bit
This bit connects/disconnects the Resistor 3 Wiper to the Resistor 3 Network
1 = P3W pin is connected to the Resistor 3 Network
0 = P3W pin is disconnected from the Resistor 3 Network
R3B: Resistor 3 Terminal B (P3B pin) Connect Control bit
This bit connects/disconnects the Resistor 3 Terminal B to the Resistor 3 Network
1 = P3B pin is connected to the Resistor 3 Network
0 = P3B pin is disconnected from the Resistor 3 Network
R2HW: Resistor 2 Hardware Configuration Control bit
This bit forces Resistor 2 into the “shutdown” configuration of the Hardware pin
1 = Resistor 2 is NOT forced to the hardware pin “shutdown” configuration
0 = Resistor 2 is forced to the hardware pin “shutdown” configuration
R2A: Resistor 2 Terminal A (P0A pin) Connect Control bit
This bit connects/disconnects the Resistor 2 Terminal A to the Resistor 2 Network
1 = P2A pin is connected to the Resistor 2 Network
0 = P2A pin is disconnected from the Resistor 2 Network
R2W: Resistor 2 Wiper (P0W pin) Connect Control bit
This bit connects/disconnects the Resistor 2 Wiper to the Resistor 2 Network
1 = P2W pin is connected to the Resistor 2 Network
0 = P2W pin is disconnected from the Resistor 2 Network
R2B: Resistor 2 Terminal B (P2B pin) Connect Control bit
This bit connects/disconnects the Resistor 2 Terminal B to the Resistor 2 Network
1 = P2B pin is connected to the Resistor 2 Network
0 = P2B pin is disconnected from the Resistor 2 Network
R3HW
R/W-1
TCON1 BITS
W = Writable bit
‘1’ = Bit is set
R/W-1
R3A
(1)
R/W-1
R3W
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R/W-1
R3B
R2HW
R/W-1
x = Bit is unknown
R/W-1
R2A
© 2009 Microchip Technology Inc.
R/W-1
R2W
R/W-1
R2B
bit 0