MCP4342-503E/ST Microchip Technology, MCP4342-503E/ST Datasheet - Page 37

• Manufacturer Part Number: MCP4342-503E/ST
• Description: IC DGTL POT QUAD 50K 14TSSOP
• Manufacturer: Microchip Technology
• Series: WiperLock™r

Specifications of MCP4342-503E/ST

• Taps: 129
• Resistance (ohms): 50K
• Number Of Circuits: 4
• Temperature Coefficient: 150 ppm/°C Typical
• Memory Type: Non-Volatile
• Interface: SPI Serial
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 14-TSSOP
• Resistance In Ohms: 50K
• End To End Resistance: 50kohm
• Track Taper: Linear
• Resistance Tolerance: ± 20%
• No. Of Steps: 129
• Supply Voltage Range: 2.7V To 5.5V
• Control Interface: Serial, SPI
• No. Of Pots: Quad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

REGISTER 4-2:
© 2009 Microchip Technology Inc.
bit 8
Legend:
R = Readable bit
-n = Value at POR
bit 8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Note 1:
R-1
D8
These bits do not affect the wiper register values.
D8: Reserved. Forced to “1”
R1HW: Resistor 1 Hardware Configuration Control bit
This bit forces Resistor 1 into the “shutdown” configuration of the Hardware pin
1 = Resistor 1 is NOT forced to the hardware pin “shutdown” configuration
0 = Resistor 1 is forced to the hardware pin “shutdown” configuration
R1A: Resistor 1 Terminal A (P1A pin) Connect Control bit
This bit connects/disconnects the Resistor 1 Terminal A to the Resistor 1 Network
1 = P1A pin is connected to the Resistor 1 Network
0 = P1A pin is disconnected from the Resistor 1 Network
R1W: Resistor 1 Wiper (P1W pin) Connect Control bit
This bit connects/disconnects the Resistor 1 Wiper to the Resistor 1 Network
1 = P1W pin is connected to the Resistor 1 Network
0 = P1W pin is disconnected from the Resistor 1 Network
R1B: Resistor 1 Terminal B (P1B pin) Connect Control bit
This bit connects/disconnects the Resistor 1 Terminal B to the Resistor 1 Network
1 = P1B pin is connected to the Resistor 1 Network
0 = P1B pin is disconnected from the Resistor 1 Network
R0HW: Resistor 0 Hardware Configuration Control bit
This bit forces Resistor 0 into the “shutdown” configuration of the Hardware pin
1 = Resistor 0 is NOT forced to the hardware pin “shutdown” configuration
0 = Resistor 0 is forced to the hardware pin “shutdown” configuration
R0A: Resistor 0 Terminal A (P0A pin) Connect Control bit
This bit connects/disconnects the Resistor 0 Terminal A to the Resistor 0 Network
1 = P0A pin is connected to the Resistor 0 Network
0 = P0A pin is disconnected from the Resistor 0 Network
R0W: Resistor 0 Wiper (P0W pin) Connect Control bit
This bit connects/disconnects the Resistor 0 Wiper to the Resistor 0 Network
1 = P0W pin is connected to the Resistor 0 Network
0 = P0W pin is disconnected from the Resistor 0 Network
R0B: Resistor 0 Terminal B (P0B pin) Connect Control bit
This bit connects/disconnects the Resistor 0 Terminal B to the Resistor 0 Network
1 = P0B pin is connected to the Resistor 0 Network
0 = P0B pin is disconnected from the Resistor 0 Network
R1HW
R/W-1
TCON0 BITS
W = Writable bit
‘1’ = Bit is set
R/W-1
R1A
(1)
R/W-1
R1W
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R/W-1
R1B
R0HW
R/W-1
MCP434X/436X
x = Bit is unknown
R/W-1
R0A
R/W-1
R0W
DS22233A-page 37
R/W-1
R0B
bit 0